AMN Construction
AMN Construction · Trade School · Insulation and air sealing

Trade School · course 13 of 28

Insulation and air sealing. A sweater and a windbreaker.

Insulation slows heat; air sealing stops drafts. A house needs both, and the South Coast’s mild climate has let many older houses go without either. This course opens a wall and an attic, compares every insulation type, follows fiberglass from molten glass to a batt, and walks the energy code from 1978 to today.

7 chapters32 3D scenes10 min readSanta Barbara South CoastChecked 19 Nov 2026

The 3D scenes need WebGL, which this browser has turned off. Every word of the course is still here on the left.

Chapter 1 of 7

Inside an insulated wall.

A modern wall controls heat, air and moisture, each with its own layer.

Three jobs, three layers

Insulation slows heat flow. An air barrier stops air moving through the wall. A weather barrier keeps rain out. Good assemblies give each job a clear layer.

R-value

R-value measures resistance to heat flow: the higher, the slower. A 2x4 wall cavity filled with batts is roughly R-13 to R-15; a 2x6 cavity roughly R-19 to R-21.

WhyR-value only counts if the insulation fills the cavity with no gaps or compression.

Studs leak heat

Wood conducts heat much faster than insulation, so every stud is a small bridge. Continuous rigid foam outside the sheathing covers those bridges.

Chapter 2 of 7

Every insulation in the yard.

Each type fits a different cavity, budget and goal.

Batts and wool

Fiberglass batts are the most common and least expensive. Mineral wool is denser, holds its shape, and is noncombustible, useful in walls between rooms and near fire exposure.

Blown cellulose

Shredded, recycled paper treated with borates for fire and pests, blown into attics or dense-packed into closed walls.

WhyDense-pack cellulose can insulate an old plaster wall through small holes, without opening it.

Spray foam

Open-cell foam is soft, air-seals and lets moisture pass. Closed-cell foam is rigid, has higher R-value per inch and stops vapor.

Boards and barriers

Rigid foam board goes outside sheathing, under slabs and on foundation walls. Radiant barriers reflect heat in hot attics.

Chapter 3 of 7

From sand to a pink batt.

Fiberglass is glass spun into fibers finer than a hair and bound into a springy mat.

Six stations

Sand and recycled glass are melted, spun into fibers by spinning discs, coated with a binder, cured in an oven into a mat, cut into batts, and compressed into bags.

Spinning

Molten glass flows into spinners with thousands of tiny holes; centrifugal force throws out fibers that are caught in a stream of air and binder.

Air does the work

The glass is not what insulates. The still air trapped between the fibers is. That is why a crushed batt loses R-value.

Chapter 4 of 7

Installed right: seal first, then fill.

The best insulation fails if air flows around it.

Seal the attic floor first

Before insulation, every hole into the attic is sealed: top plates, wire and pipe holes, light fixtures, the chase around a flue (with fire-rated material).

WhyWarm air rising through those holes carries more heat, and moisture, than the insulation can stop.

Fill without gaps or compression

Batts are cut around wires and boxes, not stuffed behind them. Blown insulation is brought to a marked depth across the whole attic.

Inspect and test

California’s energy code can call for a HERS rater to verify insulation quality, and new homes are often blower-door tested to measure how leaky the envelope is.

Chapter 5 of 7

From no insulation to Title 24.

For most of the twentieth century, South Coast houses were built with no insulation at all.

1920s: none

Plaster, wood and air. In Santa Barbara’s mild climate, many houses from this era still have empty walls and an uninsulated attic.

1950s: a little in the attic

Some post-war houses got a few inches of mineral wool or loose fill in the attic. Some loose fills from this era, like vermiculite, may contain asbestos and should be tested.

1978: the first energy code

California adopted its first building energy efficiency standards, Title 24 Part 6, in 1978. Wall and ceiling insulation became standard in new houses.

2000s: foam and testing

Spray foam in the rafter bays under the roof deck, sealed attics, and third-party verification of insulation and duct leakage spread through each code cycle.

Today

The 2025 Energy Code, in force since 1 January 2026, sets insulation by climate zone and verifies it, alongside heat-pump heating and cooling.

Chapter 6 of 7

The same trade, on a real ADU.

Every course ends on one building: a 710-square-foot ADU on Canon Drive in the Santa Barbara foothills, modelled from its permit set before pricing. Three gables, three floor levels, a steel canopy, and a list of questions the drawings left open. Here is the envelope, and what the energy report decided.

R-20 walls

All exterior walls are insulated to R-20. Penetrations are sealed and rodent-proofed, as CALGreen requires, before the walls are closed.

Vaulted ceilings

Every room is vaulted to the roof, so the roof insulation fills the rafter bays. The energy report in Submittal 3 makes the roof unvented, with closed-cell spray foam to at least R-30 against the underside of the deck.

The inspection before drywall

Insulation is inspected before drywall. If the energy report calls for a quality-insulation check, a HERS rater looks at every bay before it is covered.

Chapter 7 of 7

What it means for your house.

Insulation is cheapest when the walls are already open, and the attic is the easiest win.

The attic first

In most older South Coast houses, sealing and insulating the attic is the single most effective energy improvement and needs no walls opened.

Vented or sealed attic

Most attics are vented: insulation lies on the ceiling and air flows from the eaves to the ridge to keep the roof dry. A sealed attic moves the insulation up under the roof deck, often as spray foam, so the attic is inside the house and ducts up there stay at room temperature. In fire zones, vented attics need ember-resistant vents; sealed attics have none.

WhySealing an attic is a design decision, not a patch: it changes how the roof dries and how the energy model counts the ducts.

Walls when they are open

In a remodel, open walls get insulated and sealed before drywall. Closed plaster walls can be dense-packed from outside or inside through small holes.

Insulation outside the studs

Every stud is a path for heat that the cavity insulation cannot stop. A layer of rigid foam outside the sheathing covers them all. Furring strips over it hold the siding or stucco lath, windows get deeper extension jambs, and the water-resistive barrier still goes behind or over the foam as designed.

WhyExterior foam changes window and door details. It is decided early so window flanges, flashing and trim depth are drawn for it.

Insulating a closed wall

An old wall can be insulated without opening it: a small hole is drilled in each stud bay, from outside or in, and cellulose is blown in densely enough that it will not settle. Where fire blocking or bracing crosses the bay, a second hole goes below it. The holes are plugged and patched to match.

WhyOld houses often have wiring like knob-and-tube in the walls. That wiring must be checked or replaced before insulation goes around it.

Comfort and quiet

Insulation between rooms and floors cuts sound, which owners often notice more than the energy savings.

The blower door test

A blower door is a fan in a red frame sealed into an outside doorway. It pulls air out of the house to a set pressure, and a gauge reads how much air leaks back in through every crack. While it runs, a tester finds the leaks with a puff of smoke or a thermal camera.

WhyRunning the test before drywall, while leaks can still be sealed, is cheaper than failing it at the end.

Insulating below grade

A basement or wine room wall is cool concrete with damp soil behind it. Fiberglass against it gathers condensation, and a plastic sheet behind drywall traps moisture between two cold layers. The usual safe assembly is rigid foam or closed-cell spray foam bonded to the concrete, so the first surface warm air touches is above its dew point, then a stud wall and drywall. The room is kept dry with the HVAC or a dehumidifier.

WhyBelow grade, moisture management decides how long the finishes last. The waterproofing outside and the insulation inside are one system.

Holes in the ceiling

The ceiling under an attic is full of holes: recessed lights, the attic hatch, bath fans, pipes and wires. Warm indoor air leaks through every one, carrying heat in winter and dust and moisture into the attic. California's energy code asks that recessed lights in an insulated ceiling be rated for contact with insulation and airtight; the hatch gets rigid insulation on top and a gasket; and every penetration is sealed with foam or caulk before the insulation goes on.

WhyInsulation does little over an unsealed ceiling. Seal first, insulate second, and check the light fixtures on the submittal.

The attic edge

Where the roof meets the wall, a vented attic needs two things that fight for the same space: air moving in from the soffit vents and insulation at full depth over the top of the wall, the coldest corner of the ceiling. Baffles stapled between the rafters hold an air channel open above the insulation, and a dam at the edge keeps blown insulation from spilling into the eave and choking the vents. Raised-heel trusses, where they are designed, give the insulation room to be full depth all the way out.

WhyMold on the ceiling corners and blocked soffit vents usually start at this one detail. Install baffles before the insulation crew arrives.

Foam needs a cover

Spray foam and foam board are plastics, and the building code does not allow them exposed to a living space. They are separated from the interior by a thermal barrier, usually half-inch drywall, or by a coating or assembly that has been tested for it. In attics and crawlspaces entered only for service, a lighter ignition barrier or a listed intumescent coating may be allowed instead. The foam maker's evaluation report says which.

WhyExposed foam in a finished garage or bonus room is a failed inspection. Plan the covering when the foam is chosen.

After the film

Use it on a real house.

On your house

Insulation and air sealing make a house quieter as well as cheaper to heat. The open-wall stage of a remodel is the moment to do it well.

For our crew

The AMN crew trains on the full private set for this trade: a 3D job site you walk station by station, the lesson plan, the field guide, the math and the tools. Sign-in is not needed, but these pages are kept out of search.

Trades in this course

  • Insulation · C-2
  • Air sealing and building performance

All 100 trades

Before you hire

In California, a license is needed for any job of $1,000 or more in labor and materials, any job that needs a permit, or any job where the worker hires help. Look up the contractor’s license number at cslb.ca.gov and check it is active and carries the right class:

  • Insulation: CSLB class C-2

On the job: the install checklist.

The install chapter as a list to walk before you call the work done. Ticks stay in this browser only. Prints on one page.

Insulation and air sealing · Job: ________________ · Date: __________ · Checked by: ________________

Check yourself. Out loud.

The same drill our crew uses: give the answer in two sentences before you open each one. If you can only name the thing, read that chapter again.

01 R-valueSay why it matters, then open

R-value only counts if the insulation fills the cavity with no gaps or compression.

From chapter: Inside an insulated wall

02 Blown celluloseSay why it matters, then open

Dense-pack cellulose can insulate an old plaster wall through small holes, without opening it.

From chapter: Kinds of insulation

03 Vented or sealed atticSay why it matters, then open

Sealing an attic is a design decision, not a patch: it changes how the roof dries and how the energy model counts the ducts.

From chapter: Your house

04 Insulating a closed wallSay why it matters, then open

Old houses often have wiring like knob-and-tube in the walls. That wiring must be checked or replaced before insulation goes around it.

From chapter: Your house

05 Insulating below gradeSay why it matters, then open

Below grade, moisture management decides how long the finishes last. The waterproofing outside and the insulation inside are one system.

From chapter: Your house

06 The attic edgeSay why it matters, then open

Mold on the ceiling corners and blocked soffit vents usually start at this one detail. Install baffles before the insulation crew arrives.

From chapter: Your house

Words in this course.

16 terms in plain English, with the Spanish our crew uses. All 249 words across the school are on one page.

Air barrier Barrera de aire
The continuous layer that stops air leaking through the walls and ceiling.
Batt Colchoneta de aislante
A pre-cut blanket of fiberglass or mineral wool that fits between studs.
Bay Crujía
One repeating section of a building front: a window and the wall around it.
Blower door Prueba de puerta sopladora
A fan set in a doorway that pressurizes the house to measure how leaky it is.
Eave Alero
The low edge of a roof that hangs over the wall.
Flashing Tapajuntas
Thin metal or membrane that steers water away from a joint, such as around a window.
Jamb Jamba
The frame a door or window sits in.
Lath Malla
The mesh or strips that plaster is spread onto.
R-value Valor R
How well a material resists heat flow. Higher is better.
Rafter Cabio
A sloped beam that holds up the roof.
Ridge Cumbrera
The top line of a roof.
Sheathing Entablado
The plywood skin nailed over the wall and roof framing.
Soffit Sofito
The underside of a roof overhang, a beam or an arch.
Stud Montante
One of the upright framing pieces inside a wall.
Submittal Entrega para aprobación
Product information or a sample sent to the architect for approval.
Thermal bridge Puente térmico
A path, like a wood stud or steel beam, that carries heat around the insulation.

Questions people ask.

Do older Santa Barbara houses have insulation?

Often not in the walls, and only a little in the attic. California’s energy code began in 1978; many houses built before then had none.

What is the best insulation for an older house?

Usually: seal and insulate the attic first, then insulate walls when they are open in a remodel. Closed plaster walls can be dense-packed with cellulose through small holes.

What is R-value?

A measure of resistance to heat flow. Higher is better, but only if the insulation fills the space with no gaps or compression and air is sealed around it.

Is spray foam worth it?

In the right places: sealed attics, rim joists, and where high R-value per inch matters. It costs more than batts or cellulose and needs careful installation.

How should a basement or below-grade wall be insulated?

With rigid foam or closed-cell spray foam bonded to the concrete, then a stud wall and drywall. Fiberglass against cool concrete gathers condensation, and a plastic sheet behind the drywall traps moisture. The room is kept dry with the HVAC system or a dehumidifier.

Sources and checks

Rules change with each code cycle, and the plans, the inspector, the adopted code and the maker’s instructions overrule any course. Code references are to the 2025 California Building Standards Code (Title 24), in force since 1 January 2026; check the local amendments of the city or county. This page was checked against these on 18 November 2026:

  • California Energy Commission, Title 24 Part 6 (first standards 1978; 2025 Energy Code effective 1 January 2026)
  • Title 24 Part 6 mandatory and prescriptive insulation measures; HERS field verification (quality insulation installation, envelope leakage)
  • U.S. EPA, vermiculite insulation and asbestos guidance
  • North American Insulation Manufacturers Association, how fiberglass is made
  • AMN crew field guide: Insulation and air sealing
  • California Residential Code R316 (foam plastic, thermal and ignition barriers)

Ask about your house

Matt Newman · 805 886 0988 · purchasing@amnbuild.com