AMN Construction

Trade School · course 14 of 28

Plumbing. Water in under pressure, water out by gravity.

A house has two plumbing systems that never touch: pressurized supply bringing clean water in, and gravity drains carrying waste out, with vents letting them breathe. This course cuts open every pipe you will find in a South Coast house, follows copper tube from billet to coil, and walks a century from galvanized steel and cast iron to PEX.

7 chapters42 3D scenes12 min readSanta Barbara South CoastChecked 19 Nov 2026

The 3D scenes need WebGL, which this browser has turned off. Every word of the course is still here on the left.

Chapter 1 of 7

Two systems that never touch.

Supply pipes are small and pressurized. Drain pipes are large, sloped and full of air.

Supply: small, under pressure

Supply lines carry water from the meter at street pressure, usually reduced to about 50 to 80 psi in the house. Because they are pressurized, they can run uphill and around corners.

Drains: large, sloped, by gravity

Drain pipes run downhill at about 1/4 inch per foot for small lines, so waste flows without pumps. They are much larger than supply pipes because they carry air as well as water.

WhyToo flat and solids settle. Too steep and water runs ahead of the solids and leaves them behind.

Traps and vents

Every fixture has a trap, a U-bend that holds water to block sewer gas, and every trap needs a vent pipe to the roof so draining water cannot siphon it dry.

WhyGurgling drains and sewer smells usually mean a vent problem.

Chapter 2 of 7

Every pipe you will find in a South Coast house.

A house remodeled over 70 years can have five kinds of pipe in one wall.

Galvanized steel

Zinc-coated steel pipe, threaded together, was the standard supply pipe into the 1950s. It rusts from the inside, narrowing until the pressure drops to a trickle.

WhyBrown water and weak showers in an older house usually mean galvanized pipe at the end of its life.

Copper

Copper tube, soldered at the joints, replaced galvanized after the war. Type L has a thicker wall than Type M. It lasts decades, though aggressive water can pinhole it.

PEX and CPVC

PEX is flexible cross-linked polyethylene, run in long lengths with few joints. CPVC is rigid plastic, glued. PEX is now the most common supply pipe in new work.

Drains: cast iron, ABS, clay

Cast iron drains are heavy and quiet and were standard until the 1970s; old ones crack and scale inside. Black ABS plastic took over. The sewer lateral to the street was often clay tile, which roots love.

Chapter 3 of 7

From a copper billet to seamless tube.

Copper plumbing tube is pierced, extruded and drawn, without a seam.

Six stations

Copper is cast into round billets, heated, pierced and extruded into a thick tube, then drawn through dies over an internal plug until the wall is thin and exact.

Hard and soft copper

Drawn tube is hard and comes in straight lengths. Annealed tube is soft and comes in coils that can be bent by hand.

The color stripe

Copper tube is printed along its length with a color code: green for Type K, blue for Type L and red for Type M, from the thickest wall to the thinnest.

WhyThe stripe tells you the wall thickness without measuring.

Chapter 4 of 7

Plumbed right: slope, vent, test.

Plumbing inspections look at the same things every time.

Slope, support, protect

Drains are sloped and supported at intervals so they do not sag. Where pipes pass through studs near the face, steel plates protect them from screws.

Pressure and heat

A pressure regulator protects fixtures from street pressure. Water heaters get an expansion tank where required, seismic straps, and in new work heat-pump units.

Santa Barbara: California requires water heaters to be strapped against earthquakes.

Test before covering

Before walls close, the supply is pressure-tested and drains are filled with water or air and held while the inspector checks for drops.

Chapter 5 of 7

A hundred years of South Coast plumbing.

Every generation of pipe had a reason, and most have a known failure.

1920s: galvanized and cast iron

Threaded galvanized supply and heavy cast iron drains, often with lead joints. Sewers ran to clay tile laterals.

1950s: copper, and Orangeburg

Copper supply spread after the war. Some sewer laterals used Orangeburg, a tar-soaked wood-fiber pipe that deforms and collapses with age.

1970s to 1990s: plastic, and polybutylene

ABS replaced cast iron for drains. Gray polybutylene supply pipe was widely used from the late 1970s into the 1990s and later failed in many houses.

Around 2010: PEX in California

After years of regulatory fights, PEX was approved for statewide use in California around 2009 to 2010 and became the common supply pipe.

Today

PEX or copper supply, ABS or cast iron drains, low-flow fixtures, and heat-pump water heaters as the code’s new baseline.

Santa Barbara: Drought made water use a local issue: California limits flow on showerheads, faucets and toilets, and districts like Montecito Water District have imposed restrictions in dry years.

Chapter 6 of 7

The same trade, on a real ADU.

Every course ends on one building: a 710-square-foot ADU on Canon Drive in the Santa Barbara foothills, modelled from its permit set before pricing. Three gables, three floor levels, a steel canopy, and a list of questions the drawings left open. Here is the plumbing for a small house with two baths.

Under the slab

A 3-inch building drain at a quarter inch per foot runs under all three slabs, with a stub-up at every fixture. It is tested with water or air before the gravel goes back.

Water from a manifold

The water lines run from a manifold in the water-heater closet to each fixture. The heater is a split heat-pump unit: a tank inside, a compressor on a pad outside, so it draws no room air, which answers the City's venting question.

The powder room toilet

Powder room 102 scales about 47 inches wall to wall. A standard elongated toilet leaves 17 to 20 inches in front, and the code calls for 24. A compact or wall-hung bowl fits; the red patch is the shortfall.

Vents through the roof

Vents rise through the roof and get roof jacks before the tile goes on. The shower valve and the supply stub-outs are set at top-out, and the shower walls are tiled at least 6 feet up.

Chapter 7 of 7

What it means for your house.

Before a kitchen or bath remodel, we trace the pipes from the meter to the sewer.

Repipe when the walls are open

If a remodel opens most walls, replacing old galvanized supply with PEX or copper costs a fraction of what it does later.

Shower valves

Every shower valve must protect against scalding. A pressure-balance valve keeps the temperature steady when someone flushes a toilet. A thermostatic valve holds a set temperature and usually adds separate volume control, common where there are several heads. The valve body is set to the depth marked on its box so the trim fits after tile.

WhyA valve set too deep or too shallow is the most common reason shower trim does not fit. It is checked at rough inspection, before tile.

Home-run PEX and the manifold

With PEX, supply lines can run from a central manifold to each fixture with no joints in the walls: hot and cold manifolds side by side, a shutoff for every line, each one labeled. One fixture can be shut off without affecting the rest of the house.

WhyFewer fittings hidden in walls means fewer places to leak. Smaller lines to each fixture also bring hot water faster.

Rough-in heights

Fixtures go where the rough plumbing puts them, so heights are set before the walls close: a shower valve around 48 inches and the head around 80, a toilet flange 12 inches from the finished wall, sink supplies around 20 inches and the drain around 18. All are measured from the finished floor, not the subfloor, and checked against the fixtures actually ordered.

WhyA wall-mounted faucet or a tall person's shower head is easy at rough-in and a wall repair afterward. Fixture choices are made before the plumber starts.

Scope the sewer

The sewer lateral, from the house to the city main, is the owner's to maintain. We run a camera through the cleanout before a major remodel: roots at the joints, sags and breaks in old clay or Orangeburg pipe are common, and are best found before new floors go in. The fix is lining the old pipe or replacing it. A backwater valve protects houses that sit lower than the street.

WhyA scope costs little compared with a backup into a new floor.

Water heaters and fixtures

A new kitchen or bath is the moment for a heat-pump water heater, recirculation for faster hot water, and fixtures that meet California’s flow limits.

Setting a toilet

A toilet that never rocks or leaks starts below it: the flange is fastened down and sits on top of the finished floor, centered 12 inches from the finished wall, with closet bolts in its slots. A wax ring or foam seal goes between, the bowl is pressed down level and the bolts snugged, not cranked, and the base is caulked with a small gap at the back so a leak would show.

WhyA flange left below a thick new tile floor is the classic cause of a slow leak. Raise it with an extender before setting.

Strapping the water heater

California requires every tank water heater to be strapped to the wall in the upper and lower thirds so it cannot topple in an earthquake and break its gas line. Connections are flexible, the relief valve is piped to a safe place, and a pan with a drain goes under it where a leak would do damage.

WhyA toppled gas water heater is a common cause of fires after an earthquake. Two straps and flexible connectors prevent it.

Heat pump water heaters and hot water on demand

The 2025 code points new homes to heat pump water heaters: a tank with a small heat pump on top that pulls heat from the surrounding air, so it needs room to breathe or ducts, a condensate drain and a 240-volt circuit. A small recirculation pump on a timer or a push-button at the far bath brings hot water quickly without running the tap.

WhyA heat pump water heater in a closet without enough air runs slowly and noisily. The location is chosen at design, not when the old tank fails.

Installing appliances

Most appliance callbacks are install details (the appliances here are pulled out from the wall to show them): a range needs its anti-tip bracket, a dishwasher drain loops up high or runs to an air gap so dirty water cannot siphon back, a refrigerator's ice maker connects at a recessed box with its own shutoff, and a washer gets a recessed box with hot, cold and drain and, upstairs, a drain pan.

WhyA range without its anti-tip bracket can tip onto a child standing on the open door. It is a two-screw part that often stays in the box.

Where the water comes in

City water reaches the house from the meter through a main shutoff and, where street pressure runs high, a pressure regulator set near 60 psi. Any treatment, a softener or a whole-house filter, goes after it with a bypass so it can be serviced, and every hose bib has a backflow preventer so garden water cannot siphon back.

WhySouth Coast water is hard, which scales water heaters and fixtures. Whether to soften is a choice; where the loop and drain for it go is decided at rough-in.

Gas piping

Gas runs from the utility meter through a shutoff valve and, on most South Coast houses, an automatic seismic shutoff valve. Outdoors it is usually painted black steel; indoors, flexible yellow CSST is common and must be bonded to the electrical ground. Every appliance gets its own shutoff and a sediment trap, and new piping is pressure-tested before it is covered.

WhyA seismic valve shuts the gas after a strong earthquake, when broken lines cause fires. Many local rules require one on sale or remodel.

Leak detection and automatic shutoff

A slow leak inside a wall or under a floor can run for weeks in a house that is often empty. A leak-detection system puts a flow meter and a motorized shutoff valve on the main line, and water sensors under sinks, dishwashers, water heaters and the laundry. When it sees water where it should not be, or flow that never stops, it closes the valve and sends an alert.

WhySecond homes are where these pay for themselves. Install the valve where it can be reached and serviced, with a manual bypass.

Water treatment

South Coast water is hard: it leaves scale on glass, fixtures and inside heaters. Whole-house systems usually start with sediment and carbon filters, then a softener or a scale-reduction unit, plus a drinking-water filter at the kitchen. Each is installed with bypass valves so it can be serviced. Some California agencies restrict salt softeners that discharge to the sewer, so the type is checked with the local rules.

WhyScale shortens the life of a tankless heater, a steam generator and every valve in the house. Plan the space before the walls close.

Freestanding tubs

A freestanding tub has no wall to hide its plumbing, so the drain and a floor-mounted filler are roughed in from below, located from the tub maker's drawing to the inch. A cast-iron or stone tub full of water and a person can weigh well over a thousand pounds, so the floor framing is checked before the tub is chosen. On a slab, the drain and supply locations are set before the pour.

WhyOrder the tub, or at least its cut sheet, before rough plumbing. A drain an inch off shows forever.

Laundry to landscape

A clothes washer can water a garden. In a California one- or two-family house, a laundry-to-landscape system that does not cut into the existing plumbing can be built without a construction permit, if it meets the conditions in the plumbing code. The washer's own pump sends the water through a three-way valve to purple-marked pipe and into mulch basins under the plants, never to the surface or a lawn, and never stored.

WhyIt is cheap, it works, and the City of Santa Barbara publishes how to do it. Use plant-friendly detergent.

Pressure from the street

Water mains on the South Coast's hills can deliver more pressure than a house should see, and the plumbing code requires a pressure-reducing valve when static pressure is over 80 psi. The valve sits near where the line enters the house, with a gauge to set it, commonly between 50 and 70 psi. Once the house has a pressure regulator or a check valve, it is a closed system, and the water heater needs an expansion tank to absorb the water that heating pushes back.

WhyHigh pressure shortens the life of every valve, hose and fixture in the house. Test it on day one with a gauge on a hose bib.

Santa Barbara: Pressure varies widely across Santa Barbara and Montecito with elevation; downhill lots often see the highest.

Cleanouts you can reach

Every drain clogs eventually, and a cleanout is the door the plumber uses to clear it. The code asks for them at the base of stacks, at changes of direction sharper than forty-five degrees, at the end of horizontal runs and where the building drain leaves the house, and it asks that they stay accessible. In a finished house that means an access panel, a cleanout in the floor of a closet or a two-way cleanout outside, never one buried behind tile.

WhyA buried cleanout turns a one-hour call into demolition. Mark every one on the as-built drawings.

Water hammer

When a washing machine, dishwasher or a single-lever faucet shuts water off instantly, the moving column of water slams to a stop and the pipes bang, sometimes hard enough to loosen fittings. A water hammer arrestor, a small sealed piston chamber installed near the quick-closing valve, absorbs the shock. Washer boxes often come with them built in. High street pressure makes hammer worse, which is one more reason to set the pressure regulator.

WhyBanging pipes are not just noise; they shake joints loose inside walls. Add arrestors at the machines while the wall is open.

Scald protection

Hot water can scald in seconds, and a toilet flushed elsewhere in the house can make a shower suddenly hotter. The plumbing code asks that shower and tub-shower valves be pressure-balancing or thermostatic, holding temperature steady when pressure changes, and that their limit stop be set so the outlet stays at or below 120 degrees Fahrenheit. The plumber sets the stop at trim-out with a thermometer, not by feel.

WhyValves ship with the limit stop at its widest. Set it and test it before the owner moves in.

After the film

Use it on a real house.

On your house

Plumbing is where hidden age costs money. A camera down the sewer and a look at the supply lines come before we price a kitchen or bath.

For our crew

The AMN crew trains on the full private set for this trade: a 3D job site you walk station by station, the lesson plan, the field guide, the math and the tools. Sign-in is not needed, but these pages are kept out of search.

Trades in this course

  • Plumbing · C-36
  • Gas piping · C-36
  • Sewer lateral · C-42
  • Water treatment · C-55
  • Appliance installation

All 100 trades

Before you hire

In California, a license is needed for any job of $1,000 or more in labor and materials, any job that needs a permit, or any job where the worker hires help. Look up the contractor’s license number at cslb.ca.gov and check it is active and carries the right class:

  • Plumbing: CSLB class C-36
  • Sewer lateral: CSLB class C-42
  • Water treatment: CSLB class C-55

On the job: the install checklist.

The install chapter as a list to walk before you call the work done. Ticks stay in this browser only. Prints on one page.

Plumbing · Job: ________________ · Date: __________ · Checked by: ________________

Check yourself. Out loud.

The same drill our crew uses: give the answer in two sentences before you open each one. If you can only name the thing, read that chapter again.

01 Drains: large, sloped, by gravitySay why it matters, then open

Too flat and solids settle. Too steep and water runs ahead of the solids and leaves them behind.

From chapter: Inside the pipes

02 The color stripeSay why it matters, then open

The stripe tells you the wall thickness without measuring.

From chapter: How copper pipe is made

03 Scope the sewerSay why it matters, then open

A scope costs little compared with a backup into a new floor.

From chapter: Your house

04 Installing appliancesSay why it matters, then open

A range without its anti-tip bracket can tip onto a child standing on the open door. It is a two-screw part that often stays in the box.

From chapter: Your house

05 Leak detection and automatic shutoffSay why it matters, then open

Second homes are where these pay for themselves. Install the valve where it can be reached and serviced, with a manual bypass.

From chapter: Your house

06 Pressure from the streetSay why it matters, then open

High pressure shortens the life of every valve, hose and fixture in the house. Test it on day one with a gauge on a hose bib.

From chapter: Your house

Words in this course.

13 terms in plain English, with the Spanish our crew uses. All 249 words across the school are on one page.

ABS Tubo ABS
Black plastic drain pipe, glued with solvent cement.
Cleanout Registro
A capped opening in a drain line for clearing clogs.
Elevation Alzado
A flat, straight-on drawing of one side of a building or one wall of a room.
Graywater Aguas grises
Used water from washers, showers and basins that can irrigate a garden.
Heat pump Bomba de calor
An electric machine that both heats and cools a house by moving heat, not making it.
PEX PEX, tubería flexible
Flexible plastic water pipe joined with crimped or expanded fittings.
Pressure-reducing valve Válvula reductora de presión
A valve that lowers street water pressure to a safe level for the house.
Sediment trap Trampa de sedimentos
A short capped leg of gas pipe that catches debris before an appliance.
Stud Montante
One of the upright framing pieces inside a wall.
Trap Trampa, sifón
The U-shaped bend under a fixture that holds water to keep sewer gas out.
Vent Ventilación
A pipe up through the roof that lets air into the drains so traps are not sucked dry.
Water hammer Golpe de ariete
The bang in pipes when a valve closes fast; stopped with arrestors.
Water hammer arrestor Amortiguador de golpe de ariete
A small cushioned chamber that absorbs the shock when a valve slams shut.

Questions people ask.

How do I know if my house has galvanized pipes?

Look where pipes enter at the water heater or under a sink: galvanized pipe is dull gray steel with threaded joints. A magnet sticks to it but not to copper or plastic.

Should I repipe during a remodel?

If the house has old galvanized supply or the walls will be open anyway, usually yes. It costs far less with walls open than as a separate job later.

What is Orangeburg pipe?

A wood-fiber pipe soaked in tar, used for some sewer laterals from the 1940s to the 1970s. It deforms and collapses with age; a camera inspection finds it.

Is PEX allowed in California?

Yes. PEX is approved for water supply in California and is now the most common supply pipe in new residential work.

What water pressure is too high for a house?

The plumbing code requires a pressure-reducing valve when street pressure is over 80 psi. Most houses are set between 50 and 70 psi.

Do I need a permit for a laundry-to-landscape graywater system in Santa Barbara?

Not if it meets the conditions in the California Plumbing Code: a clothes washer system in a one- or two-family house that does not cut into the existing plumbing. The washer pumps through a three-way valve to mulch basins below the surface. The City of Santa Barbara publishes a fact sheet with the conditions.

Is a whole-house leak detection valve worth it?

In a house that is often empty, yes. A flow meter and motorized valve on the main line, with sensors under sinks, the water heater and the laundry, close the water and send an alert when a leak starts, before it runs for weeks.

Sources and checks

Rules change with each code cycle, and the plans, the inspector, the adopted code and the maker’s instructions overrule any course. Code references are to the 2025 California Building Standards Code (Title 24), in force since 1 January 2026; check the local amendments of the city or county. This page was checked against these on 18 November 2026:

  • California Plumbing Code (drainage slope, traps and venting, water heater seismic strapping, pressure regulation)
  • ASTM B88 (seamless copper water tube, Types K, L and M) and Copper Development Association copper tube handbook
  • California Building Standards Commission approval of PEX for statewide use (2009 to 2010)
  • California Energy Commission Title 20 appliance efficiency standards (fixture flow limits)
  • AMN crew field guide: Plumbing
  • California Plumbing Code, pressure-reducing valve above 80 psi; cleanout requirements
  • California Plumbing Code: shower valves of the pressure-balance or thermostatic type, limited to 120 °F
  • California Plumbing Code Chapter 15 (alternate water sources): clothes washer systems exempt from a construction permit when the listed conditions are met
  • City of Santa Barbara, Graywater Fact Sheet

Ask about your house

Matt Newman · 805 886 0988 · purchasing@amnbuild.com