AMN Construction
AMN Construction · Trade School · Drywall and plaster

Trade School · course 20 of 28

Drywall and plaster. Flat, smooth, and harder than it looks.

A smooth wall is the most visible craft in a house and one of the least understood. This course takes apart a sheet of drywall and an old plaster wall, explains the five levels of finish, follows gypsum from rock to board, and walks a century from wood lath to Level 5.

7 chapters34 3D scenes10 min readSanta Barbara South CoastChecked 19 Nov 2026

The 3D scenes need WebGL, which this browser has turned off. Every word of the course is still here on the left.

Chapter 1 of 7

Inside drywall and old plaster.

Most South Coast houses built before about 1950 have plaster walls. Almost everything since has drywall.

A sheet of drywall

Drywall, also called gypsum board or Sheetrock, is a core of gypsum between two layers of paper. Sheets are screwed to studs, the joints are taped and covered with joint compound, then primed and painted.

Gypsum resists fire

Gypsum is about one-fifth water locked in its crystals. In a fire, that water has to boil off before the board fails, which slows the fire. Type X board adds glass fibers for rated walls.

Lath and plaster

Older walls are wood lath strips with gaps between them. Wet plaster pushed through the gaps curls behind the lath into "keys" that hold the wall on. Two or three coats make it thick, hard and quiet.

WhyWhen plaster keys break, ceilings sag. Plaster washers or adhesive can reattach it.

Chapter 2 of 7

Boards, compounds and levels of finish.

The right board for the room, and the right level of finish for the light.

Pick the board

Regular board for walls and ceilings, Type X where a fire rating is needed such as garage walls next to living space, moisture-resistant board in baths outside the shower, cement board behind tile in wet areas.

Compounds

Premixed all-purpose compound dries by evaporation. Setting compound is a powder that hardens by chemical reaction, faster and harder, used for first coats and repairs.

Levels 0 to 5

Each level adds to the one before: Level 0 is hung board, Level 1 sets tape in compound, Level 2 adds a coat over tape and screws, Level 3 a second coat, Level 4 a third, feathered wide. Level 3 suits textured walls; Level 4 is common for flat paint; Level 5 adds a skim coat over the whole surface for walls hit by raking light or glossy paint.

WhyLow-angle light from a big window will find every seam in anything less than Level 5.

Chapter 3 of 7

From gypsum rock to a stack of board.

Drywall is made on a continuous line hundreds of feet long.

Seven stations

Gypsum rock (or synthetic gypsum from power plants) is crushed and heated to drive off water, mixed back into a slurry, spread between two moving sheets of paper, cut, dried and bundled.

It sets like plaster

Adding water back to calcined gypsum makes it recrystallize and harden within minutes, which is why the line can cut boards while they are still moving.

Chapter 4 of 7

Hung right, finished right.

A good finish starts with how the board is hung.

Hang to minimize joints

Board goes on long edges perpendicular to framing, with end joints staggered and never on the edge of a door or window opening, where they crack.

Tape and three coats

Joints get tape bedded in compound, then two more coats, each wider and thinner, sanded between coats.

Dust control

Sanding compound releases fine dust that can contain silica. Low-dust compounds, vacuum sanders and containment protect the rest of the house.

Chapter 5 of 7

From lath to Level 5.

Interior walls changed from a craft to a product, and part of the craft came back.

1920s: wood lath and plaster

Three-coat plaster on wood lath, hard and slightly wavy, in the houses built during and after the 1925 rebuilding.

1940s: rock lath

Small gypsum lath panels, often 16 by 48 inches, replaced wood lath. They were nailed across the studs and still finished with two or three coats of plaster.

1960s: drywall takes over

Drywall made walls faster and cheaper in the post-war boom.

1960s to 1980s: popcorn and texture

Sprayed textures hid imperfect finishing. Older textures and some joint compounds of the period may contain asbestos.

Today

Smooth Level 4 and Level 5 walls, veneer plaster where clients want the old hardness, and low-dust finishing.

Chapter 6 of 7

The same trade, on a real ADU.

Every course ends on one building: a 710-square-foot ADU on Canon Drive in the Santa Barbara foothills, modelled from its permit set before pricing. Three gables, three floor levels, a steel canopy, and a list of questions the drawings left open. Here is drywall in a house with no flat ceilings.

The ceilings vault

The rooms vault to the roof, so the drywall follows the rafters up to the ridge beams. That means more cutting at the valleys and the step in the roof, and more scaffolding than a flat ceiling.

5/8-inch board, moisture-resistant in wet rooms

The walls and ceilings are 5/8-inch drywall, with moisture-resistant board in the wet areas and cement backer in the shower.

Light decides the finish

Big south sliders throw low light across the walls, which shows every seam. Walls that get raking light need a higher level of finish than the ones in shade.

Chapter 7 of 7

What it means for your walls.

Matching old walls is often harder than building new ones.

Keep the plaster or not

Sound plaster is worth keeping: it is harder and quieter than drywall. Where we open walls, we patch with plaster or with drywall shimmed and skimmed to the same plane.

Venetian plaster and tadelakt

Polished lime plasters give walls depth that paint cannot. Venetian plaster goes on in thin coats with crossing trowel strokes and is burnished with a steel trowel until it shines. Tadelakt, a Moroccan lime plaster, is polished with a stone and sealed with soap, and can line a shower when it is done by someone who knows it.

WhyThese finishes show every wave in the wall under them. The substrate is skimmed to Level 5 first, and a sample board is approved before the room is done.

Fixing cracks in old plaster

A crack in old plaster is opened into a shallow V so the patch has something to grip, bridged with mesh tape, filled with setting compound, which hardens like plaster, and finished in wider and wider coats until it disappears. Loose plaster is reattached to the lath with plaster washers first.

WhyCracks that come back in the same place are moving. Find out why, often settling or a missing header, before patching again.

The wall between garage and house

The wall and ceiling between an attached garage and the house separate a car and its fuel from where people sleep. They get Type X fire-rated board on the garage side, taped; the door between is solid or fire-rated and self-closing; and every hole for pipes, wires or ducts is sealed with fire-rated caulk.

WhyA door propped open or a hole cut for a cable undoes the separation. Inspectors look at both.

Test before sanding

In houses from before the 1980s, textures and compounds are tested for asbestos before anyone sands or demolishes them.

Light decides the level

Rooms with big windows and raking light, and walls painted in sheen, are worth Level 5.

Arches and rounded corners

Spanish Colonial Revival interiors are full of arched openings and soft corners. The header above the opening carries the load; the arch below it is built from plywood cut to a template, wrapped in flexible corner bead or lath, and plastered by hand so the curve and the edges read soft.

WhyAn arch that is a perfect machine curve with crisp corners looks new. The hand-rounded edge is what makes it read as old.

Quiet walls

A wall stops sound with mass, a break and a seal: insulation in the cavity, resilient channel so the drywall is not screwed tight to the studs, two layers of board, and acoustic sealant around every edge and outlet. A media room or a bedroom next to a laundry is where it pays off.

WhyA gap the size of a pencil around an outlet can undo most of what the wall gains. The sealant matters as much as the layers.

Trimless lights and shadow reveals

In a clean modern room the light fixtures have no visible trim and the wall stops short of the ceiling with a thin dark line. Both are drywall details: a trimless fixture has a flange that is set in the board and finished over, and a reveal is a metal bead that leaves a crisp gap. Both have to be installed before taping, perfectly straight, and finished to Level 5, because raking light shows everything.

WhyThese details cost little in material and a lot in care. Mock one up and let the owner see it before the whole house is done.

Plaster cornices and ornament

Older houses here often have cornices of real plaster: either run in place, by pulling a sheet-metal knife cut to the profile along wet plaster, or cast in molds and set in pieces. Ceiling medallions and brackets are cast. To repair one, a plasterer takes a profile from a sound section, cuts a matching knife and runs the missing length so it meets the old cornice without a seam.

WhyWood or foam crown cannot match a run plaster cornice up close. Repair the plaster when it is original.

Barrel vaults and groin vaults

A curved ceiling starts in the framing: ribs cut from plywood to the exact radius, set close together, with blocking where two vaults cross. Over them goes flexible drywall, bent in thin layers, or metal lath for plaster. The line where the curve meets the wall, the spring line, has to be dead level, or the vault looks twisted from every doorway.

WhyThe framer builds the shape and the plasterer can only follow it. Check the ribs with a template before any board goes up.

Corner bead

Every outside corner of drywall gets a bead that defines the edge and protects it. Plain metal bead nailed on is the old standard; it is tough but its edges can crack away from the compound as the house moves. Paper-faced beads, set in compound like tape, bond with the finish and crack far less. Bullnose beads give the softly rounded corners that suit Spanish Colonial and plaster-look interiors. Whichever is used, it is chosen once and used throughout so every corner reads the same.

WhyA rounded corner in the living room and a square one in the hall looks like a mistake. Decide the corner before the hangers start.

Screws and pops

Drywall is screwed to the framing at the spacing the board maker and the code call for, closer on ceilings than on walls, and each screw is driven just below the surface without tearing the face paper, so the compound can cover it. Pops, the small round bumps that appear months later, are screws standing proud after wet framing has shrunk or a board was not pressed tight before driving. The fix is to drive a new screw beside it and recoat, but the cure is dry framing.

WhyPops in the first year are a lumber-moisture problem as much as a drywall problem. Check the framing before the board goes up.

Paper tape or mesh

Joints in drywall are reinforced with tape, and the two kinds are not interchangeable. Paper tape is strong, creases cleanly for inside corners and works with any compound. Self-adhesive fiberglass mesh is quick on flat seams but stretches, so it should be bedded in a setting-type compound that hardens chemically, not in ready-mixed compound that dries; otherwise the joint can crack. Most finishers use paper for corners and butt joints and choose mesh case by case.

WhyCracked seams on ceilings are often mesh tape in the wrong compound. Agree on the system before the finishers start.

Ceilings first

Hangers board the ceilings before the walls. The wall sheets then go up tight under the ceiling edge and help support it, and the corner where they meet is cleaner to tape. Sheets run perpendicular to the framing in the longest lengths that can be handled, so there are fewer butt joints, and those that remain are staggered and kept away from the corners of doors and windows, where cracks begin.

WhyA butt joint lined up with a window corner will crack. Lay out the sheets before cutting.

After the film

Use it on a real house.

On your house

Walls are the canvas for everything else. We match old plaster where it stays and finish new walls to the light they will face.

For our crew

The AMN crew trains on the full private set for this trade: a 3D job site you walk station by station, the lesson plan, the field guide, the math and the tools. Sign-in is not needed, but these pages are kept out of search.

Trades in this course

  • Drywall · C-9
  • Interior plaster · C-35
  • Acoustical · C-2

All 100 trades

Before you hire

In California, a license is needed for any job of $1,000 or more in labor and materials, any job that needs a permit, or any job where the worker hires help. Look up the contractor’s license number at cslb.ca.gov and check it is active and carries the right class:

  • Drywall: CSLB class C-9
  • Interior plaster: CSLB class C-35
  • Acoustical: CSLB class C-2

On the job: the install checklist.

The install chapter as a list to walk before you call the work done. Ticks stay in this browser only. Prints on one page.

Drywall and plaster · Job: ________________ · Date: __________ · Checked by: ________________

Check yourself. Out loud.

The same drill our crew uses: give the answer in two sentences before you open each one. If you can only name the thing, read that chapter again.

01 Lath and plasterSay why it matters, then open

When plaster keys break, ceilings sag. Plaster washers or adhesive can reattach it.

From chapter: Two kinds of wall

02 Venetian plaster and tadelaktSay why it matters, then open

These finishes show every wave in the wall under them. The substrate is skimmed to Level 5 first, and a sample board is approved before the room is done.

From chapter: Your house

03 The wall between garage and houseSay why it matters, then open

A door propped open or a hole cut for a cable undoes the separation. Inspectors look at both.

From chapter: Your house

04 Trimless lights and shadow revealsSay why it matters, then open

These details cost little in material and a lot in care. Mock one up and let the owner see it before the whole house is done.

From chapter: Your house

05 Barrel vaults and groin vaultsSay why it matters, then open

The framer builds the shape and the plasterer can only follow it. Check the ribs with a template before any board goes up.

From chapter: Your house

06 Screws and popsSay why it matters, then open

Pops in the first year are a lumber-moisture problem as much as a drywall problem. Check the framing before the board goes up.

From chapter: Your house

Words in this course.

22 terms in plain English, with the Spanish our crew uses. All 249 words across the school are on one page.

Bead Baquetón
A small half-round molding.
Bullnose Canto boleado
A fully rounded edge on stone or tile.
Cornice Cornisa
The top, projecting part of a wall or entablature. Indoors, a large crown molding.
Crown Corona
The molding where the wall meets the ceiling.
Lath Malla
The mesh or strips that plaster is spread onto.
Level 5 Nivel 5
The smoothest drywall finish: a thin coat of compound over the whole wall.
Profile Perfil
The outline of a molding if you slice through it.
Rafter Cabio
A sloped beam that holds up the roof.
Reveal Reveal
A small, deliberate step or gap between two surfaces. Also the depth of wall you see at a window.
Reveal bead Perfil de entrecalle
A metal trim that leaves a crisp shadow gap in drywall.
Ridge Cumbrera
The top line of a roof.
Run cornice Cornisa corrida en sitio
A plaster cornice shaped in place by pulling a profile knife along it.
Section Sección
A drawing of a building or part as if sliced through.
Sheen Brillo
How shiny a finish is.
Spanish Colonial Revival Spanish Colonial Revival
The white-plaster, red-tile style that defines Santa Barbara, built mostly 1915 to 1930.
Spring line Línea de arranque
The level line where an arch or vault starts to curve.
Stud Montante
One of the upright framing pieces inside a wall.
Tadelakt Tadelakt
A polished, water-resistant lime plaster from Morocco.
Trimless Sin moldura
A modern detail with no visible trim; surfaces meet at a clean line or a thin gap.
Valley Lima hoya
A sloped inside corner of a roof, where water collects.
Veneer plaster Yeso de acabado delgado
A thin, hard coat of plaster troweled over a special gypsum base board.
Venetian plaster Estuco veneciano
Polished lime plaster with depth and a soft shine.

Questions people ask.

What is a Level 5 drywall finish?

The highest standard finish: after taping and coating, the entire surface gets a thin skim coat so the paper and compound look the same under paint and raking light.

Should I keep my old plaster walls?

If they are sound, usually yes: plaster is harder, quieter and original to the house. Cracks and loose areas can be repaired; sections opened for remodeling can be patched to match.

Does popcorn ceiling contain asbestos?

Ceiling textures applied before the 1980s may. Have it tested before scraping or remodeling.

What drywall goes in a bathroom?

Moisture-resistant board outside the shower; cement board or a foam board with a waterproof membrane behind tile in the wet area.

How is a barrel-vaulted ceiling built?

In the framing. Ribs are cut from plywood to the exact radius and set close together, then covered with thin flexible drywall or metal lath and plaster. The line where the curve meets the wall has to be dead level or the vault looks twisted.

Can an old plaster cornice be repaired to match?

Yes. A plasterer takes the profile from a sound section, cuts a sheet-metal knife to it and runs the missing length in wet plaster so it meets the old cornice without a seam.

Sources and checks

Rules change with each code cycle, and the plans, the inspector, the adopted code and the maker’s instructions overrule any course. Code references are to the 2025 California Building Standards Code (Title 24), in force since 1 January 2026; check the local amendments of the city or county. This page was checked against these on 18 November 2026:

  • California Residential Code R702 (interior wall covering) and Table R702.3.5 (fastening)
  • Gypsum Association GA-214 (recommended levels of gypsum board finish) and GA-216 (application and finishing)
  • Cal/OSHA 8 CCR 1532.3 (respirable crystalline silica)
  • USG Gypsum Construction Handbook (manufacture, veneer plaster)
  • AMN crew field guide: Drywall and plaster

Ask about your house

Matt Newman · 805 886 0988 · purchasing@amnbuild.com