AMN Construction
AMN Construction · Trade School · Floors and paint

Trade School · course 23 of 28

Floors and paint. The surfaces you touch every day.

Floors and paint are the last trades in and the ones you live with most. This course takes a wood floor apart from the joists up, compares every flooring you will find on the South Coast, opens a can of paint, and walks a century from old-growth fir and lead paint to engineered planks and low-VOC finishes.

7 chapters36 3D scenes10 min readSanta Barbara South CoastChecked 19 Nov 2026

The 3D scenes need WebGL, which this browser has turned off. Every word of the course is still here on the left.

Chapter 1 of 7

Inside a hardwood floor.

A wood floor is only as good as what is under it.

From the joists up

Joists, a plywood subfloor glued and screwed to stop squeaks, a layer of underlayment paper, the flooring nailed through its tongue, then sanding and finish.

Flat and dry first

The subfloor is checked for flatness and moisture before any flooring goes down; wood is acclimated to the house.

WhyWood moves with humidity. Flooring laid over a damp crawlspace or a wet slab will cup.

Tongue and groove

Each board’s tongue fits the next board’s groove and is nailed at an angle through the tongue, so nails are hidden and boards can move slightly.

Chapter 2 of 7

Every floor, and what is in the can.

Choose a floor for how a room is used; choose paint for the surface and the light.

Solid and engineered wood

Solid boards can be sanded and refinished many times. Engineered planks have a real wood wear layer on a stable plywood core: wider boards, less movement, and fewer refinishings.

Old fir and terracotta

Many 1920s and 1930s houses have old-growth Douglas fir floors, softer than oak but rich in color, and Saltillo or clay tile in Spanish rooms.

Vinyl plank

Luxury vinyl plank is waterproof and inexpensive; it cannot be refinished and its quality varies widely.

Primer and sheen

Primer seals and bonds; finish paint brings color and durability. Flatter sheens hide flaws; glossier sheens clean easily and show every bump.

Chapter 3 of 7

From pigment to a tinted gallon.

Paint is pigment, binder, solvent and additives, ground and mixed to a recipe.

Six stations

Titanium dioxide and fillers are dispersed at high speed, let down with the binder, tested, canned, and tinted with colorants at the store.

VOCs

Volatile organic compounds evaporate as paint dries. California air districts, including Santa Barbara County’s, cap VOC content in architectural coatings, and most interior paint today is low-VOC water-based acrylic.

Chapter 4 of 7

Done right: prep is ninety percent.

A good paint job is mostly preparation; a good floor finish is mostly dust control.

Prep

Fill, sand, caulk and spot-prime; protect floors and fixtures; test old paint for lead before sanding in a pre-1978 house.

Prime and two coats

New drywall and patches get primer; most finishes need two coats for even color and sheen.

Floors last

Wood floors are usually sanded and finished near the end, with the house sealed and quiet; waterborne finishes cure faster and smell less than oil.

Chapter 5 of 7

A hundred years of floors and finishes.

Floors got wider and paint got safer.

1920s: old-growth fir and oak

Narrow fir and oak strip floors, finished with shellac or varnish, and lead-based paint on the trim.

1950s: tile and linoleum

Asphalt and vinyl-asbestos tile, linoleum and wall-to-wall carpet covered many original floors.

1978: lead paint banned

Lead paint was banned for homes; the layers already on old trim remain the main lead hazard in renovations.

2000s: engineered and wide

Engineered planks made wide boards practical over slabs and radiant heat.

Today

Low-VOC waterborne finishes, engineered wood, vinyl plank, and the original fir uncovered and refinished.

Chapter 6 of 7

The same trade, on a real ADU.

Every course ends on one building: a 710-square-foot ADU on Canon Drive in the Santa Barbara foothills, modelled from its permit set before pricing. Three gables, three floor levels, a steel canopy, and a list of questions the drawings left open. Here is flooring on three levels.

Oak on three levels

The model shows oak floors through the living, bedroom, hall and primary, stepping up with the slab. Every step gets a matching wood tread with a nosing and a closed riser.

Treads at the steps

Three risers from kitchen to hall and two more to the primary: with three risers or fewer, no handrail is required, but the nosings and risers have to be equal to within the code's tolerances.

Paint last

Prime and paint come after cabinets and trim. With vaulted ceilings up to the ridge, the paint crew needs the same scaffolding the drywall crew used.

Chapter 7 of 7

What it means for your rooms.

Look under the carpet before you buy new flooring.

Original floors under carpet

In many older South Coast houses, original fir or oak is under carpet or vinyl and can be sanded and refinished.

Test the slab, let the wood settle

Wood and many resilient floors fail from moisture coming up through concrete. The slab is tested, often with probes set into it and read after a day, and a moisture barrier goes down where readings are high. Wood flooring sits in the house for days before installation so it reaches the same moisture as the rooms.

WhyA floor that cups or gaps a few months after install is almost always a moisture problem, not a product problem.

Sand and refinish an old floor

A solid wood floor can be refinished several times. It is sanded to bare wood in three passes, coarse to fine, with the edges done by a smaller sander; gaps are filled, stain goes on if wanted, and two or three coats of finish follow, with light sanding between. Water-based finishes dry fast and stay clear; oil-based ones amber with age.

WhyEngineered floors have a thin top layer that may take only one sanding, or none. Check the wear layer at a floor register before promising a refinish.

Carpet, done right

Carpet lasts when it is stretched tight. Tack strips go around the room a small gap from the wall, the pad is laid between them with taped seams, and the carpet is pulled across with a power stretcher and hooked onto the strips. Seams run with the light and away from doorways.

WhyCarpet that ripples within a year was knee-kicked instead of power-stretched. Old carpet over a good fir or oak floor is worth lifting first; see the next stop.

Matching old floors

Patching an old floor needs reclaimed or matched boards woven in, then sanding the whole room together.

Herringbone and chevron

Patterned wood floors start from a center line snapped on the room's main view, usually from the entry. Herringbone uses left- and right-hand planks set at right angles; chevron cuts the ends to meet in a point. Pieces are glued and nailed, and a border of straight boards often frames the field at the walls.

WhyPattern floors use more material and many more cuts. Order extra, and lay out dry in the room before the first plank is glued.

Exterior paint and the coast

Salt air and sun are hard on paint. Good prep, primer and breathable coatings on stucco last longest.

The right primer for the surface

Paint fails at the bond, so the primer is chosen for what it goes on: bare wood gets a wood primer, stained or tannin-rich wood a stain-blocking primer, galvanized metal a bonding primer (never oil paint), and new stucco or plaster waits to cure before a masonry primer. Each sample here shows the bare surface, the primer stripe and the finish.

WhyPeeling paint is almost always the wrong primer or a surface that was not clean, dry and dull before painting.

Wallcovering

Wallpaper and grasscloth show every flaw under them, so the wall is skimmed smooth and primed with a wallcovering primer. Fine papers go over a liner hung the other way. The first strip hangs from a plumb line, the pattern is matched across each seam, and seams are butted, never overlapped and never on top of a liner seam.

WhyPattern repeat decides how much to order. A large repeat can waste a third of each roll, so the paper is measured from the wall, not the floor area.

Limestone and stone floors

Honed limestone, travertine and marble floors are set in a full bed of mortar with no hollow spots, over a membrane that keeps slab cracks from reaching the stone, on a floor stiff enough for stone. The tile is sealed before grouting so grout cannot stain it, and again after. Limestone is softer than it looks: acids from wine and lemon etch it, so owners need the care sheet on day one.

WhyA stone floor that cracks or sounds hollow was set on a bouncy floor or with spotty mortar. Both are avoidable.

Wide planks and oil finishes

Wide oak planks move more with humidity than narrow strips, so they are usually engineered, delivered early to acclimate, and laid only when the wood and the subfloor measure within the maker's moisture range. Many high-end floors are finished on site with a hardwax oil rather than a polyurethane: it looks matte and natural and a worn spot can be repaired without sanding the whole room, but it needs re-oiling every few years.

WhyGaps in winter and cupping in summer are moisture, not bad wood. A moisture meter on the first day avoids both.

Parquet panels

Versailles and other parquet floors come as square panels, each a frame around an interlaced lattice of oak. The installer snaps a grid from the center of the room so the panels finish evenly at every wall, then glues each one down over a flat, stiff subfloor. They are usually sanded and finished in place, so the joints between panels disappear.

WhyA panel floor shows any error in the layout lines across the whole room. The layout is the job.

Leave room to grow

Wood takes on and gives off moisture with the seasons and swells and shrinks across its width. A wood floor needs a gap at every wall and fixed object, commonly about half to three quarters of an inch, as the manufacturer specifies, hidden by the baseboard and shoe. A floating floor needs the same and cannot be pinned down by heavy cabinets or an island set on top of it. A floor run tight to the walls buckles the first damp winter.

WhyCheck the gap before base goes on; afterwards it cannot be seen until the floor lifts.

Nosings for engineered floors

An engineered wood floor has a thin wear layer on a plywood core, so its edge cannot be left exposed or rounded over at the top of a stair or a step-down. Manufacturers make matching stair nosings, flush or overlapping, that are glued and fastened to the stair and cover the end grain. The nosing comes from the same production run as the flooring when possible so the color matches, and it is ordered with the floor, not afterwards.

WhyNosings are a separate line item and can be weeks out. Order them with the floor or the stairs wait.

Stain samples on the real floor

Wood stain looks different on every species, every sanding grit and in every light, so the color is chosen from samples on the actual floor, sanded the way the whole floor will be, with the actual finish over them. The owner looks at them in daylight and at night under the house lights, and signs off on one. A chip from a showroom or a photo on a phone is not a sample.

WhyGetting the stain wrong means sanding the whole floor again. Sample, sign, then stain.

Keep a wet edge

Paint dries from the edges in, and where fresh paint is rolled over paint that has started to dry, the overlap shows as a darker or shinier band, flashing, especially in eggshell and satin sheens and in raking light. Painters cut in one wall at a time and roll it right away, working from the cut edge into wet paint, finishing each wall in one go with consistent pressure. Primer under patches keeps them from flashing too.

WhyFlashing on a long wall is a technique problem, not a paint problem. Cut and roll a wall at a time.

After the film

Use it on a real house.

On your house

Floors and paint are where a remodel starts to look finished. We protect them through the job and finish them last.

For our crew

The AMN crew trains on the full private set for this trade: a 3D job site you walk station by station, the lesson plan, the field guide, the math and the tools. Sign-in is not needed, but these pages are kept out of search.

Trades in this course

  • Hardwood flooring · C-15
  • Resilient and carpet flooring · C-15
  • Painting · C-33
  • Wood finishing · C-33
  • Wallcovering · C-33

All 100 trades

Before you hire

In California, a license is needed for any job of $1,000 or more in labor and materials, any job that needs a permit, or any job where the worker hires help. Look up the contractor’s license number at cslb.ca.gov and check it is active and carries the right class:

  • Hardwood flooring: CSLB class C-15
  • Painting: CSLB class C-33

On the job: the install checklist.

The install chapter as a list to walk before you call the work done. Ticks stay in this browser only. Prints on one page.

Floors and paint · Job: ________________ · Date: __________ · Checked by: ________________

Check yourself. Out loud.

The same drill our crew uses: give the answer in two sentences before you open each one. If you can only name the thing, read that chapter again.

01 Flat and dry firstSay why it matters, then open

Wood moves with humidity. Flooring laid over a damp crawlspace or a wet slab will cup.

From chapter: Inside a floor

02 Sand and refinish an old floorSay why it matters, then open

Engineered floors have a thin top layer that may take only one sanding, or none. Check the wear layer at a floor register before promising a refinish.

From chapter: Your house

03 Herringbone and chevronSay why it matters, then open

Pattern floors use more material and many more cuts. Order extra, and lay out dry in the room before the first plank is glued.

From chapter: Your house

04 Limestone and stone floorsSay why it matters, then open

A stone floor that cracks or sounds hollow was set on a bouncy floor or with spotty mortar. Both are avoidable.

From chapter: Your house

05 Parquet panelsSay why it matters, then open

A panel floor shows any error in the layout lines across the whole room. The layout is the job.

From chapter: Your house

06 Nosings for engineered floorsSay why it matters, then open

Nosings are a separate line item and can be weeks out. Order them with the floor or the stairs wait.

From chapter: Your house

Words in this course.

18 terms in plain English, with the Spanish our crew uses. All 249 words across the school are on one page.

Baseboard Zoclo
The board along the bottom of a wall.
Chevron Chevrón
A floor pattern of boards cut on a slant so they meet in neat points.
Crack-isolation membrane Membrana antifisuras
A sheet under tile or stone that keeps slab cracks from telegraphing through.
Cupping Acanalado
A board curling across its width.
End grain Testa
The cut end of a board, where the growth rings show.
Flashing Tapajuntas
Thin metal or membrane that steers water away from a joint, such as around a window.
Grain Veta
The lines and direction of the fibers in wood.
Grout Lechada
The filler in the joints between tiles.
Handrail Pasamanos
The rail you hold on a stair.
Hardwax oil Aceite de cera dura
A wipe-on finish that soaks into wood and leaves a flat, natural look. Easy to touch up.
Herringbone Espiga (patrón)
A floor pattern of rectangular boards laid in a zigzag.
Honed Apomazado
Stone ground smooth but not shiny.
Nosing Nariz
The front edge of a stair tread.
Ridge Cumbrera
The top line of a roof.
Sheen Brillo
How shiny a finish is.
Shellac Goma laca
An old natural clear coat, wiped or brushed on. Beautiful, but marked by water.
Tongue and groove Machihembrado
Boards with a ridge on one edge that slots into a channel on the next.
Tread Huella
The part of a stair you step on.

Questions people ask.

Can I refinish my old fir floors?

Usually, yes. Old-growth Douglas fir is softer than oak but can be sanded and refinished, often several times, if the boards are thick enough.

Solid or engineered hardwood?

Solid wood can be refinished more times. Engineered wood is more stable, comes in wider boards and works over slabs and radiant heat.

Is my old paint lead paint?

If the house was built before 1978, assume painted trim and windows may contain lead until tested. Sanding or scraping it requires lead-safe work practices.

What paint sheen should I use?

Flat or matte for ceilings and most walls, eggshell for living areas, satin or semi-gloss for trim, doors, kitchens and baths.

Are wide-plank oak floors a problem near the coast?

They move more with humidity than narrow strips, so they are usually engineered, delivered early to acclimate, and laid only when the wood and subfloor are within the maker's moisture range.

What is a hardwax oil floor finish?

A penetrating oil-and-wax finish that looks matte and natural. A worn spot can be repaired without sanding the room, but the floor needs re-oiling every few years.

Sources and checks

Rules change with each code cycle, and the plans, the inspector, the adopted code and the maker’s instructions overrule any course. Code references are to the 2025 California Building Standards Code (Title 24), in force since 1 January 2026; check the local amendments of the city or county. This page was checked against these on 18 November 2026:

  • National Wood Flooring Association installation guidelines (subfloor, moisture, acclimation)
  • Santa Barbara County Air Pollution Control District, architectural coatings rule (VOC limits)
  • CARB Suggested Control Measure for Architectural Coatings
  • U.S. CPSC 1978 ban on lead paint for residential use; EPA RRP rule (40 CFR 745)
  • AMN crew field guide: Floors and paint

Ask about your house

Matt Newman · 805 886 0988 · purchasing@amnbuild.com