AMN Construction
AMN Construction · Trade School · Finish carpentry

Trade School · course 25 of 28

Finish carpentry. Where a house is judged up close.

Finish carpentry is the trim, doors, stairs and built-in pieces you touch and see every day, and the trade AMN is built on. Tom has fifty years at the bench. This course takes a door opening apart, compares the woods and profiles, follows a board through the molder, and walks a century of South Coast trim from deep plaster returns to shop-milled profiles.

7 chapters40 3D scenes11 min readSanta Barbara South CoastChecked 19 Nov 2026

The 3D scenes need WebGL, which this browser has turned off. Every word of the course is still here on the left.

Chapter 1 of 7

A doorway, piece by piece.

A trimmed opening is a jamb, casings, a head detail and the baseboard that dies into it.

Jamb, casing, head, base

The jamb lines the opening and carries the door. Casing covers the joint between jamb and wall. The head casing and cap finish the top; baseboard runs along the floor and stops against the casing.

The reveal

Casing is set back from the jamb edge by a small, even step, usually about 3/16 inch. That reveal is what makes trim look crisp and hides small irregularities.

WhyA reveal that wanders from 1/8 to 1/4 inch is what the eye catches first.

The head detail

Head casings can be a simple flat board, a mitered frame, or a built-up head with a cap and crown, each a style choice tied to the house.

Chapter 2 of 7

Woods, MDF and profiles.

Paint-grade or stain-grade decides the material; the house decides the profile.

Paint-grade

Poplar is the classic paint-grade hardwood: stable and smooth. MDF is flat and cheap but dents and swells if wet. Finger-jointed pine is straight and economical.

WhyIn baths and near floors, MDF swells when it gets wet; solid wood or PVC is used there.

Stain-grade

White oak, walnut and vertical-grain fir are chosen for grain and color, matched board to board, and finished clear.

Profiles

Every molding has a profile: flat stock, ogee, cove, bead, back band. Custom profiles are ground into knives to match an old house or an architect’s drawing.

Chapter 3 of 7

From rough lumber to a milled profile.

Molding is made on a molder, which cuts all four faces of a board in one pass.

Seven steps

Dried lumber is ripped to width, run through a molder whose spinning knives cut the profile, sanded, cut to length, primed if paint-grade, and finally fitted by hand on site.

Custom knives

To match original trim in an old house, a profile is traced from a sample and ground into a set of knives, so new pieces match the old exactly.

Santa Barbara: Matching 1920s and 1930s trim profiles is routine in South Coast renovations; we keep a library of profiles we have matched.

Chapter 4 of 7

Fitted right: cope, scribe, set.

The craft is in the joints you cannot see from across the room.

Cope inside corners

Inside corners of baseboard and crown are coped: one piece runs into the corner and the other is cut to the first one’s profile. Unlike a miter, a cope stays tight when the wood shrinks.

Scribe to the floor and wall

Floors and walls are never flat. Base and casings are scribed to follow them so there is no gap to fill with caulk.

Fasten, fill, finish

Trim is nailed into framing with small finish nails, glued at joints, filled and sanded, then primed and painted or finished clear.

Chapter 5 of 7

A century of South Coast trim.

Trim is one of the best ways to date a room.

1920s: plaster returns

Many Spanish Colonial Revival houses have no window casing at all: thick plaster wraps into the opening with a rounded edge, and doors get simple, heavy wood trim.

Santa Barbara: Copying that look in an addition means building deep, rounded plaster returns, not adding trim.

Craftsman: wide and flat

Craftsman and bungalow houses on the South Coast have wide, flat casings with a cap at the head, often in stained fir.

1950s: slim and simple

Ranch houses used narrow "clamshell" or flat casings and low baseboard.

1990s: big MDF

Large MDF crown and built-up casings became common in remodels.

Today

Trim designed for the house: profiles matched to originals, shop-milled, with crisp reveals and coped joints.

Chapter 6 of 7

The same trade, on a real ADU.

Every course ends on one building: a 710-square-foot ADU on Canon Drive in the Santa Barbara foothills, modelled from its permit set before pricing. Three gables, three floor levels, a steel canopy, and a list of questions the drawings left open. Here is the finish carpentry, the last trade the owner touches every day.

Doors, casing and base

Interior doors are solid core, paint grade, 2'-6" by 7'-0". Casing and base go on after the floors, and every reveal is held the same around every opening.

Treads and nosings

The interior steps get wood treads to match the floor, with a 1-inch nosing and a closed riser. Five risers in a small house are seen up close every day.

Built-ins and closets

The built-ins and closets come from the same cabinet table as the kitchen, so the finish carpenter installs boxes that were drawn, cut and labelled from the plans.

Blocking for everything that hangs

Towel bars, robe hooks, paper holders, the TV and any shelves: the finish carpenter mounts them, but the framer has to block for them first. We listed these as owner decisions before drywall.

Chapter 7 of 7

What it means for your rooms.

Finish carpentry can be its own project, without a larger remodel.

Doors, windows and trim

Replacing or repairing doors, casing and baseboard is a project on its own, and the quickest way to change how a room feels.

Window coverings

Shades and shutters are part of the build when they are planned early: a recessed pocket framed above the window hides a roller shade, a power wire to it goes in before drywall, and interior shutters are measured to the finished opening, which on thick plaster walls is deep. On steel casements the swing of the window decides what can be mounted inside the opening.

WhyA motorized shade added after drywall means a battery motor or a cut wall. One wire at framing avoids both.

Door hardware

A good door hangs on three hinges, the top one about 5 inches from the head so the door does not sag. The lock is set back 2-3/8 or 2-3/4 inches from the edge, its latch lands in a strike mortised flush into the jamb, and the lever sits about 36 inches above the floor. Old houses often have mortise locks in the door edge, which can usually be rebuilt.

WhyA door that rubs or will not latch is almost always a hinge or strike problem, not the door. Tightening the top hinge with a long screw into the framing fixes most of them.

Stairs, mantels and beams

Stair rails and treads, fireplace mantels, ceiling beams and coffered ceilings are pieces we build in the shop and fit on site. The Cannon Drive ADU has no chimney or flue: it heats and cools with a heat pump.

Beamed ceilings and wainscot

Most decorative ceiling beams are box beams: three boards wrapped around blocking screwed to the framing, returned into a ledger at the wall and finished with corbels. Wainscot is panels or boards up the lower wall, capped with a rail. Both need blocking in the framing before drywall or plaster.

WhySolid beams are heavy and check as they dry; box beams stay straight and can hide wiring for lights. Old houses may have real beams worth keeping.

How a stair is laid out

Every step in a stair must match. The code allows a riser of 7-3/4 inches at most and a tread of at least 10 inches, with a nosing in front, and the tallest and shortest riser in a flight may differ by no more than 3/8 inch. The stringers carry the treads; the handrail sits 34 to 38 inches above the nosings.

WhyPeople trip on the step that is different. A floor finish added later can make the first or last riser wrong, so finish heights are set before the stair is built.

Matching what is there

In older houses we match original profiles, wood species and finishes so new work disappears into the old.

Trim that fits the style

Trim should match the house. Spanish Colonial Revival openings often have no casing at all, just plaster rounded into the opening. Craftsman casing is flat and wide with a thick head and cap. Colonial and Traditional casing is molded and mitered. Modern work drops the casing for a thin reveal.

WhyColonial casing on a Spanish house is one of the most common remodel mistakes design review and buyers notice.

Crown molding

Crown sits at an angle between wall and ceiling, its spring angle, so it is cut on the saw upside down and backward, or with compound settings. Outside corners are mitered; inside corners are coped like base. Blocking behind it gives the nails something to hold, and on plaster walls and wavy ceilings it is scribed or caulked so the line stays straight.

WhyCeilings in old houses are rarely flat. Crown follows the ceiling; a laser line on the wall keeps it looking level.

Coffered ceilings

A coffered ceiling is a grid of beams with recessed panels between them. It is laid out from the center of the room and the main sightlines, so the boxes at the edges are equal and lights and vents land in the middle of a panel. The beams are framed straight and square, cased with trim, and each box gets its own small crown. Every miter shows from below.

WhyLights, speakers and sprinklers have to be located on the coffer layout before rough-in, or they land on a beam.

Paneled rooms

A paneled library or study is furniture built into the walls: stiles and rails with raised or flat panels, often quartersawn oak or walnut, with the grain matched from panel to panel. It is made in the shop and finished there, then installed and scribed tight to walls and floors that are never straight. Outlets, switches and vents are located on the panel layout before rough-in.

WhyStain-grade wood cannot hide a gap with caulk. Every edge is scribed, and the walls behind are blocked for fastening.

Hidden doors

A hidden or jib door is finished to match the wall around it: the same paint, paneling or bookcase, with the base and chair rail cut through it in line. It hangs on concealed hinges and opens with a push latch. The opening is framed and blocked for heavy hinges, and the door is made stable so the hairline joint stays even.

WhyA hidden door shows the instant its joint goes crooked. It is a finish carpenter's job from framing to paint.

Flush base and reveals

In a minimal room the baseboard sits flush with the wall or is replaced by a recessed shadow line, so the wall seems to float. It is built with metal reveal beads or a recessed base set before drywall, all at one height and dead level. The floor installer and the drywall finisher have to know the detail, because there is no trim to cover their edges.

WhyMinimal details demand more precision, not less. They are drawn and mocked up before framing.

Trim is a classical order

Every piece of interior trim is a reduced piece of a classical temple. The baseboard, wainscot and chair rail are a pedestal: base, die and cap. The wall is the column. Casing or picture rail, frieze and crown are the entablature: architrave, frieze and cornice. Renaissance rule books sized everything from the column's diameter; Vignola made the Tuscan column seven diameters tall and its entablature a quarter of that. On a wall the same thinking sizes base, field and crown to the ceiling height.

WhyWhen trim looks wrong it is usually out of proportion or from the wrong family. Santa Barbara's Spanish Colonial Revival is its own dialect: thick plaster, few moldings, deep reveals and heavy timber. A Georgian crown on it is the classic local mistake.

Built-up cornices from stock parts

A big cornice does not have to be a custom profile. It can be assembled from stock pieces the way the entablature is built: a flat frieze board on the wall, a bed mold at its top, then the crown sprung across the corner, with blocking behind. Each layer is set from a level line struck around the room, not from the ceiling, which is never level, and the gap at the ceiling is scribed or hidden by the last piece.

WhyScale the stack to the room: taller ceilings get a deeper frieze and a larger crown, so the cornice stays in proportion.

Test cuts and the five-cut check

Every number in a cut list is a calculation until it is cut. Cut the test piece in scrap, measure, adjust the saw, then cut the good board. Small angle errors add up around a frame: on a six-sided ring, a tenth of a degree at each joint leaves the last corner open by about a millimeter. To true a crosscut sled, cut all four sides of a square board in turn and a fifth across the first; the taper of that last offcut is four times the sled's error. And remember wood moves across its grain with the seasons, so no cross-grain panel is ever glued rigid.

WhyA tight miter or an even reveal is decided by the setup, not the cut. Check the tool before the material.

Layout habits from Japanese joinery

Japanese temple carpenters build frames meant to last centuries and to be taken apart for repair, and several of their habits carry straight into finish work. Lay out from a snapped center line rather than a face that may not be straight, and decide on which side of each line the cut falls. A pull saw with a thin plate cuts on the pull, so it stays straight and leaves a fine kerf. A chisel or plane iron is only as good as its flattened back.

WhyExact layout and sharp tools are faster than fixing a cut. Practise on a small lattice before a stair or a door.

The right nail

Finish carpenters carry three or four nail guns because each nail has a job. Fifteen- and sixteen-gauge finish nails are thick enough to hold casing, base and jambs to framing. Eighteen-gauge brads hold small moldings, returns and door stop without splitting them. Twenty-three-gauge pins, almost headless, hold delicate parts in place while the glue does the real work. The gauge gets thinner as the number rises; the hole gets smaller and so does the hold.

WhyA heavy nail through a thin molding splits it; a pin in a heavy casing lets go. Pick by the job, not by the gun on the belt.

Sharp

A finish carpenter's chisels and plane irons are honed, not just bought sharp. The usual bevel is about twenty-five degrees, with a small secondary microbevel a few degrees steeper at the very edge that takes seconds to renew on a fine stone. A sharp tool pares end grain cleanly, fits a cope by hand and planes a scribe without tearing. A dull one crushes the fibers and leaves the fuzz that paint shows.

WhyIf the tool tears the wood, stop and hone. Five minutes at the stone saves an hour of filling and sanding.

Glue every miter

A miter nailed but not glued opens up the first dry season, because wood shrinks across its width and the two pieces pull apart at the point. Finish carpenters glue every miter, often assemble casing heads and corners on the bench with glue, a pin across the joint or a spline, and a clamp, then hang the assembled unit. The joint stays closed because it is one piece, not two pieces nailed near each other.

WhyOpen miters in the first year are the number one trim callback. Glue them; it takes seconds.

After the film

Use it on a real house.

For our crew

The AMN crew trains on the full private set for this trade: a 3D job site you walk station by station, the lesson plan, the field guide, the math and the tools. Sign-in is not needed, but these pages are kept out of search.

Trades in this course

  • Finish carpentry · C-6
  • Stair building · C-6
  • Door hardware · C-28
  • Window coverings

All 100 trades

Before you hire

In California, a license is needed for any job of $1,000 or more in labor and materials, any job that needs a permit, or any job where the worker hires help. Look up the contractor’s license number at cslb.ca.gov and check it is active and carries the right class:

  • Finish carpentry: CSLB class C-6
  • Door hardware: CSLB class C-28

On the job: the install checklist.

The install chapter as a list to walk before you call the work done. Ticks stay in this browser only. Prints on one page.

Finish carpentry · Job: ________________ · Date: __________ · Checked by: ________________

Check yourself. Out loud.

The same drill our crew uses: give the answer in two sentences before you open each one. If you can only name the thing, read that chapter again.

01 The revealSay why it matters, then open

A reveal that wanders from 1/8 to 1/4 inch is what the eye catches first.

From chapter: A trimmed doorway

02 Door hardwareSay why it matters, then open

A door that rubs or will not latch is almost always a hinge or strike problem, not the door. Tightening the top hinge with a long screw into the framing fixes most of them.

From chapter: Your house

03 Trim that fits the styleSay why it matters, then open

Colonial casing on a Spanish house is one of the most common remodel mistakes design review and buyers notice.

From chapter: Your house

04 Paneled roomsSay why it matters, then open

Stain-grade wood cannot hide a gap with caulk. Every edge is scribed, and the walls behind are blocked for fastening.

From chapter: Your house

05 Trim is a classical orderSay why it matters, then open

When trim looks wrong it is usually out of proportion or from the wrong family. Santa Barbara's Spanish Colonial Revival is its own dialect: thick plaster, few moldings, deep reveals and heavy timber. A Georgian crown on it is the classic local mistake.

From chapter: Your house

06 Layout habits from Japanese joinerySay why it matters, then open

Exact layout and sharp tools are faster than fixing a cut. Practise on a small lattice before a stair or a door.

From chapter: Your house

Words in this course.

47 terms in plain English, with the Spanish our crew uses. All 249 words across the school are on one page.

Architrave Arquitrabe
The beam that sits on the columns; the bottom part of the entablature. Door casing is the same idea.
Back band Contramarco
A strip wrapped around the outer edge of door trim to make it look thicker.
Baseboard Zoclo
The board along the bottom of a wall.
Bead Baquetón
A small half-round molding.
Bevel Bisel
A sloped edge.
Brad nail Clavo de cabeza perdida
A thin 18-gauge finish nail for small moldings.
Casement Abatible
A window that swings open on side hinges, like a door.
Casing Moldura de marco
The flat trim around a door or window.
Chair rail Guardasilla
A molding around a room at about chair-back height.
Coffer Casetón
A recessed panel in a ceiling framed by beams.
Coffered ceiling Techo de casetones
A ceiling divided into sunken squares by beams.
Cope Contraperfil
To cut the end of one molding to fit over the shape of another at an inside corner.
Corbel Ménsula
A bracket that sticks out of a wall to hold up a beam or shelf.
Cornice Cornisa
The top, projecting part of a wall or entablature. Indoors, a large crown molding.
Crown Corona
The molding where the wall meets the ceiling.
End grain Testa
The cut end of a board, where the growth rings show.
Entablature Entablamento
Everything a column holds up: the beam, the band and the projecting top.
Frieze Friso
The flat middle band of an entablature. On a wall, the band just under the crown.
Grain Veta
The lines and direction of the fibers in wood.
Handrail Pasamanos
The rail you hold on a stair.
Honed Apomazado
Stone ground smooth but not shiny.
Jamb Jamba
The frame a door or window sits in.
Jib door Puerta oculta
A hidden door made to look like part of the wall.
Kerf Corte de sierra
The slot a saw blade leaves.
MDF MDF
A smooth sheet made of fine wood fiber and glue. It takes paint well.
Microbevel Microbisel
A small, steeper bevel honed at the very edge of a chisel or plane iron.
Miter Inglete
A joint where two pieces are each cut at an angle, usually 45°, to meet in a corner.
Molding Moldura
A strip with a shaped face, used to trim and decorate.
Mortise Mortaja
A pocket cut into wood to take a tenon.
Mortise lock Cerradura de embutir
A heavy lock that fits in a pocket in the door’s edge. Found on the best doors.
Nosing Nariz
The front edge of a stair tread.
Ogee Gola
An S-shaped curve.
Pedestal Pedestal
The block a column stands on.
Picture rail Riel para cuadros
A thin molding high on a wall for hanging pictures.
Pin Pasador
In a dovetail, the piece between two tails.
Profile Perfil
The outline of a molding if you slice through it.
Proportion Proporción
How the sizes of parts relate to each other.
Quartersawn Corte radial
A board sliced so the growth rings stand upright in it. The steadiest cut.
Reveal Reveal
A small, deliberate step or gap between two surfaces. Also the depth of wall you see at a window.
Scribe Trazo a compás
To trace the shape of an uneven wall onto a piece of wood and cut it to fit.
Sightline Línea de vista
What you can see from a given spot. Also the visible width of a window frame.
Spanish Colonial Revival Spanish Colonial Revival
The white-plaster, red-tile style that defines Santa Barbara, built mostly 1915 to 1930.
Spring angle Ángulo de inclinación
The angle a crown molding leans out from the wall.
Stile Larguero
An upright piece in a frame.
Stringer Zanca
The sloped board that carries the steps of a stair.
Tread Huella
The part of a stair you step on.
Wainscot Lambrín
Wood paneling on the lower part of a wall.

Questions people ask.

What does a finish carpenter do?

Installs and builds the visible woodwork: doors, windows, casing, baseboard, crown molding, paneling, stairs, mantels, built-ins and cabinetry, fitting each piece to the house.

Why cope instead of miter inside corners?

A coped joint stays tight as the wood and the house move; an inside miter tends to open into a gap.

Can you match the trim in my old Santa Barbara house?

Yes. We trace the original profile, have knives ground to match, and mill new trim in the same species, so additions and repairs blend in.

Do you take finish carpentry jobs on their own?

Yes. Finish carpentry is taken on its own, without a larger project, from Goleta to Carpinteria. Call Tom at 818 201 4348.

Why does trim have the shapes it has?

Interior trim is a classical order in miniature. Base, wainscot and chair rail are the pedestal; casing, frieze and crown are the entablature. Sizing them to the ceiling height keeps a room in proportion.

How is a hidden door built?

The opening is framed and blocked for heavy concealed hinges, the door is made stable so its hairline joint stays even, and it is finished like the wall around it, with base and trim cut through in line.

Sources and checks

Rules change with each code cycle, and the plans, the inspector, the adopted code and the maker’s instructions overrule any course. Code references are to the 2025 California Building Standards Code (Title 24), in force since 1 January 2026; check the local amendments of the city or county. This page was checked against these on 18 November 2026:

  • Architectural Woodwork Institute, Architectural Woodwork Standards (interior millwork grades and tolerances)
  • California Residential Code R311.7 (stairways, handrails) and R312 (guards)
  • Wood Moulding and Millwork Producers Association, profile standards
  • AMN crew field guide: Finish carpentry (Tom’s fifty years at the bench)
  • Vignola, Regola delli cinque ordini (1562), via The American Vignola (Ware)

Ask about your house

Matt Newman · 805 886 0988 · purchasing@amnbuild.com