AMN Construction
AMN Construction · Trade School · Stucco and exterior plaster

Trade School · course 12 of 28 · new trade

Stucco and exterior plaster. The white walls of Santa Barbara.

The smooth, hand-troweled white wall is as much a part of Santa Barbara as the red tile above it. Underneath is a system of paper, wire and three coats of cement plaster that has to shed water for a century. This course builds one coat at a time, compares the finishes, and walks a hundred years of South Coast stucco.

7 chapters31 3D scenes10 min readSanta Barbara South CoastChecked 19 Nov 2026

The 3D scenes need WebGL, which this browser has turned off. Every word of the course is still here on the left.

Chapter 1 of 7

Inside a three-coat stucco wall.

A traditional stucco wall over wood framing is seven layers from the stud out.

Seven layers

Studs, sheathing, two layers of water-resistive paper, wire lath, then three coats of plaster: scratch, brown and finish, about 7/8 inch thick in total.

Two layers of paper

Over wood sheathing the code calls for a water-resistive barrier equal to two layers of Grade D paper. The outer layer bonds to the stucco; the inner one stays free to drain.

WhyStucco is a sponge: it absorbs water and lets it through. The paper and the drainage behind it are what keep the frame dry.

Lath gives it something to grip

Galvanized wire lath is nailed through the paper into the studs and held slightly off it, so the scratch coat squeezes through and locks around the wire.

Scratch, brown, finish

The scratch coat is raked with horizontal scratches so the brown coat bonds. The brown coat is floated flat. The finish coat carries the color and texture.

WhyEach coat cures before the next one so the wall does not crack as it shrinks.

Chapter 2 of 7

Finishes you will see on the South Coast.

The finish coat is where a stucco wall gets its character.

Smooth and hand-troweled

The smooth, slightly undulating finish of the 1920s houses is troweled by hand, with rounded corners and soft edges. It takes a skilled plasterer.

Santa Barbara: Variations are often sold as a "Santa Barbara" or "mission" finish. Design review in El Pueblo Viejo and much of Montecito favors it.

Sand float and skip trowel

Sand float gives an even, sandy texture that hides small cracks. Skip-trowel and lace finishes, popular from the 1950s, leave raised patches.

Cement, acrylic and lime

A cement finish coat with integral color breathes and ages naturally. Acrylic finishes are more flexible and brighter but trap moisture if misused. Lime plaster is soft, breathable and right for old adobe and masonry.

WhyOn an old wall, a coating that cannot breathe can trap water and blister.

Chapter 3 of 7

From limestone to a mixed batch.

Stucco is portland cement, lime, sand and water, mixed on site in a paddle mixer.

The ingredients

Portland cement and hydrated lime are both burned from limestone in kilns. Plaster sand is washed and graded. Pigment goes into the finish coat.

Lime makes it workable

Lime makes the mix creamy, slows the set, and lets the plaster heal hairline cracks over time as it slowly re-carbonates.

Mixed to the coat

Scratch and brown coats are richer in sand; the finish coat is finer and colored. Plasterers mix batch by batch so the color stays even across a wall.

Chapter 4 of 7

Done right: weep, joint, cure.

Most stucco problems are trapped water or uncontrolled cracking. Three details prevent them.

A weep screed at the bottom

At the base of the wall a metal weep screed lets water behind the stucco drain out. It sits at least 4 inches above soil, or 2 inches above paving.

WhyBury the screed in dirt or a new patio and the wall cannot drain. Rot starts at the bottom plate.

Control joints

Long walls and large panels get control joints so shrinkage cracks happen in a straight line where they are meant to.

Damp cure

Each coat is kept damp while it cures, by misting, often twice a day for the first days, and longer in hot or windy weather.

WhyPlaster that dries too fast does not cure; it cracks and dusts.

Chapter 5 of 7

A hundred years of Santa Barbara plaster.

The look has barely changed in a century. What is behind it has changed a great deal.

Lime over adobe

The Mission and the early adobes were protected with lime plaster and whitewash, renewed every few years.

1920s: plaster on wood

Early Spanish Colonial Revival houses were plastered over wood lath or wire, often over a single layer of paper or none.

Santa Barbara: After the June 1925 earthquake, the new Architectural Board of Review steered rebuilding toward the Spanish Colonial Revival look, and white plaster walls became the city’s signature.

1950s: paper and wire

Wire lath over building paper became standard, and tract houses took sprayed and skip-troweled finishes.

1980s: one-coat and foam

One-coat stucco systems over foam board arrived, faster and better insulated, with thinner, more crack-prone coats when done carelessly.

Today

Two-layer barriers or drainage mats, corrosion-resistant lath and screeds, control joints by design, and a hand-troweled finish where design review asks for it.

Chapter 6 of 7

The same trade, on a real ADU.

Every course ends on one building: a 710-square-foot ADU on Canon Drive in the Santa Barbara foothills, modelled from its permit set before pricing. Three gables, three floor levels, a steel canopy, and a list of questions the drawings left open. Here is where plaster goes on this building, and why only there.

North walls only

Three-coat cement plaster covers the north walls, the ones facing the uphill slope. Lath, scratch, brown and finish, with a weep screed at the bottom so water in the wall can drain out.

Color and finish: TBD

The finish index lists plaster EX-05 with color and texture to be decided. The bid carries an allowance per square foot until the owner chooses, and the model can show the options.

Where plaster meets wood

At the corners where the plaster walls meet the wood cladding, the two systems need a clean stop and a sealed joint. Both need the 3/16-inch drainage gap the City asked for.

Chapter 7 of 7

What it means for your walls.

Stucco tells you a lot from the outside: cracks, stains and how the base meets the ground.

Read the cracks

Hairline cracks are normal and can be bridged by the finish. Diagonal cracks off window corners, bulges, and stains below windows point to water or movement behind the wall.

Look at the bottom of the wall

If the soil, planting or paving has crept up to the weep screed, water cannot get out. It is one of the most common causes of rot we find.

Patching to match

Matching an old hand-troweled wall takes the same sand, color and hand. For a large repair we often re-coat the whole wall so it reads as one surface. The Cannon Drive ADU has no chimney or flue: it heats and cools with a heat pump.

Paint, mineral paint or limewash

Stucco can be finished four ways. Elastomeric paint forms a thick film that bridges hairline cracks but can trap moisture on old walls. Mineral paint bonds into the stucco and lets it breathe. Limewash is soft and mottled, the old look, and is renewed every few years. Or the color goes in the finish coat and there is no paint at all.

WhyOnce elastomeric paint is on, mineral paint and limewash will not stick to it. The first coating choice limits all the later ones.

Windows in a stucco wall

Where a window meets stucco, the order of layers decides whether it leaks. Sill flashing goes first, the window flange laps over it, the jamb and head flashings lap over the flange, and the second layer of paper above laps over the head flashing. The stucco stops at a casing bead with a sealant joint against the frame.

WhyStucco cracks at window corners and water finds the crack. Lapping is what sends that water back out instead of into the wall.

Wood siding and trim

Not every South Coast house is stucco. Lap and board-and-batten siding, common on Craftsman and Monterey houses and in the foothills, go over a water-resistive barrier, ideally on furring strips that leave a rain-screen gap so water drains and the back of the boards dry. Courses lap down like shingles, trim is primed on all sides, and an insect screen closes the gap at the bottom.

WhyIn fire hazard zones, siding must meet Chapter 7A: fiber cement, ignition-resistant treated wood or similar, not untreated wood.

Rounded corners and deep returns

The soft look of a Santa Barbara Spanish Colonial Revival wall comes from two plaster details: corners rounded on a bullnose bead or by hand instead of sharp, and windows set back so the plaster returns deep into the opening. The return sill slopes out so water runs off, and the window's flashing and sill pan are done before the plaster, because the deep return hides any leak until it shows inside.

WhyThe depth of the return is decided at framing by where the window sits in the wall. The plasterer can only finish what the framer set.

Plaster and the weather

Cement plaster gains strength by curing, and it needs water to do it. On a hot or windy day the surface dries before the coat underneath, and the result is crazing, weak coats and poor bond. So each coat goes onto a dampened base, the fresh work is fogged with a fine mist for the next couple of days, and on sunny or windy faces the scaffold carries shade cloth. Lime plasters want an even slower, damper cure. If a sundowner is coming, the plasterer plans around it.

WhyMost plaster cracking starts in the first 48 hours. A mister and shade cloth cost far less than a patch that never matches.

Where the joints go

Cement plaster shrinks as it cures and moves with heat and the frame behind it, and it will crack where it wants unless it is told where to crack. Control joints do the telling. The plastering standard, ASTM C1063, limits a wall panel to 144 square feet, a run to 18 feet, and a panel to no more than two and a half times as long as it is wide. Joints are best placed off the corners of windows and doors, where cracks start, and they have to be designed with the architect, because they show.

WhyAsk the architect for a joint layout before lath. On a smooth Santa Barbara wall a hairline crack is as visible as a joint, and less tidy.

Sealant joints that last

Where plaster meets a window, a door frame or another material, the gap is closed with sealant, and how it is shaped decides whether it lasts. A foam backer rod is pushed in first to set the depth and keep the sealant from sticking to the back. The bead is about twice as wide as it is deep, tooled concave, and bonded to the two sides only, so it can stretch like a rubber band as the joint moves. A thick, three-sided blob tears at the first season.

WhyAsk what sealant the window maker allows against its frame, and use the matching primer. The wrong one can fail in a year.

After the film

Use it on a real house.

On your house

A stucco wall is only as good as what is behind it. When we open one, we fix the paper and the drainage before we match the finish.

For our crew

Stucco is new to the school. The drywall and plaster job site covers the interior trade, and the windows and weatherproofing site covers the flashing every stucco wall depends on.

Trades in this course

  • Lath and plaster (stucco) · C-35
  • Siding and exterior trim

All 100 trades

Before you hire

In California, a license is needed for any job of $1,000 or more in labor and materials, any job that needs a permit, or any job where the worker hires help. Look up the contractor’s license number at cslb.ca.gov and check it is active and carries the right class:

  • Lath and plaster (stucco): CSLB class C-35

On the job: the install checklist.

The install chapter as a list to walk before you call the work done. Ticks stay in this browser only. Prints on one page.

Stucco and exterior plaster · Job: ________________ · Date: __________ · Checked by: ________________

Check yourself. Out loud.

The same drill our crew uses: give the answer in two sentences before you open each one. If you can only name the thing, read that chapter again.

01 Two layers of paperSay why it matters, then open

Stucco is a sponge: it absorbs water and lets it through. The paper and the drainage behind it are what keep the frame dry.

From chapter: Three coats

02 Cement, acrylic and limeSay why it matters, then open

On an old wall, a coating that cannot breathe can trap water and blister.

From chapter: Finishes

03 Damp cureSay why it matters, then open

Plaster that dries too fast does not cure; it cracks and dusts.

From chapter: Done right

04 Windows in a stucco wallSay why it matters, then open

Stucco cracks at window corners and water finds the crack. Lapping is what sends that water back out instead of into the wall.

From chapter: Your house

05 Rounded corners and deep returnsSay why it matters, then open

The depth of the return is decided at framing by where the window sits in the wall. The plasterer can only finish what the framer set.

From chapter: Your house

06 Where the joints goSay why it matters, then open

Ask the architect for a joint layout before lath. On a smooth Santa Barbara wall a hairline crack is as visible as a joint, and less tidy.

From chapter: Your house

Words in this course.

15 terms in plain English, with the Spanish our crew uses. All 249 words across the school are on one page.

Backer rod Cordón de respaldo
A foam rod pushed into a joint to set the depth of the sealant.
Bead Baquetón
A small half-round molding.
Bullnose Canto boleado
A fully rounded edge on stone or tile.
Casing Moldura de marco
The flat trim around a door or window.
Control joint Junta de control
A metal joint that tells plaster where to crack.
Flashing Tapajuntas
Thin metal or membrane that steers water away from a joint, such as around a window.
Jamb Jamba
The frame a door or window sits in.
Lath Malla
The mesh or strips that plaster is spread onto.
Limewash Encalado
A thin mineral paint that gives walls a soft, cloudy look.
Return Derrame
The plastered side of an opening, from the wall face back to the window.
Sheathing Entablado
The plywood skin nailed over the wall and roof framing.
Sill pan Charola de alféizar
A waterproof tray under a window that sends leaks back outside.
Spanish Colonial Revival Spanish Colonial Revival
The white-plaster, red-tile style that defines Santa Barbara, built mostly 1915 to 1930.
Stud Montante
One of the upright framing pieces inside a wall.
Weep screed Perfil de escurrimiento
A metal strip at the bottom of a plaster wall that lets trapped water drain out.

Questions people ask.

What is three-coat stucco?

A traditional portland cement plaster applied in three coats over paper and wire lath: a scratch coat, a brown coat and a finish coat, about 7/8 inch thick in total.

What is a Santa Barbara stucco finish?

A smooth, softly undulating, hand-troweled finish with rounded edges, modeled on the Spanish Colonial Revival houses built after 1925. It is often required or favored by design review on the South Coast.

Why is my stucco cracking?

Small shrinkage cracks are normal. Larger diagonal cracks, especially from window corners, can mean movement or missing control joints. Stains and bulges usually mean water behind the wall.

Can stucco be repaired to match?

Yes, with the same sand, color and troweling style. For large repairs, re-coating the whole wall avoids a visible patch.

How big can a stucco panel be between control joints?

The plastering standard ASTM C1063 limits a wall panel to 144 square feet, a run to 18 feet, and a panel to no more than two and a half times as long as it is wide.

How do Santa Barbara houses get rounded stucco corners and deep-set windows?

The corners are formed on a bullnose bead or rounded by hand, and the window is set back in a thick wall so the plaster returns into the opening. The depth is decided at framing by where the window sits; the flashing and sill pan go in before the plaster.

Sources and checks

Rules change with each code cycle, and the plans, the inspector, the adopted code and the maker’s instructions overrule any course. Code references are to the 2025 California Building Standards Code (Title 24), in force since 1 January 2026; check the local amendments of the city or county. This page was checked against these on 18 November 2026:

  • California Residential Code R703.7 (exterior plaster), R703.7.2.1 (weep screeds: 4 in above earth, 2 in above paved areas), R703.7.3 (water-resistive barriers over wood-based sheathing)
  • ASTM C926 (application of portland cement-based plaster) and ASTM C1063 (installation of lathing)
  • Portland Cement Association, Portland Cement Plaster (Stucco) Manual
  • Santa Barbara Independent and Downtown Santa Barbara histories of the 1925 earthquake and the Architectural Board of Review
  • AMN crew field guide: Drywall and plaster
  • ASTM C1063 (lathing and furring for cement plaster), control joint spacing

Ask about your house

Matt Newman · 805 886 0988 · purchasing@amnbuild.com