AMN Construction
AMN Construction · Trade School · Windows, doors and weatherproofing

Trade School · course 11 of 28

Windows, doors and weatherproofing. Every opening is a hole in the raincoat.

Most leaks in a house start at a window or a door. This course shows the layers that make an opening watertight, every kind of window you will find on the South Coast, how glass and frames are made, and a hundred years from steel casements to fire-rated dual glazing.

7 chapters37 3D scenes10 min readSanta Barbara South CoastChecked 19 Nov 2026

The 3D scenes need WebGL, which this browser has turned off. Every word of the course is still here on the left.

Chapter 1 of 7

Inside a watertight window opening.

A window installation is a sequence of overlapping layers, each one lapped so water runs out, never in.

The rough opening

Framers leave an opening a little larger than the window, typically half an inch to an inch each way, so the unit can be set plumb, level and square on shims.

The sill pan comes first

Before the window goes in, the bottom of the opening gets a sloped pan of flashing membrane or metal, turned up at the back and the ends.

WhyEvery window leaks a little eventually. The pan catches that water and sends it back outside.

Shingle-lap everything

The barrier at the sides laps over the window’s side fins, the head flashing laps over the top fin, and the barrier above laps over the head flashing.

WhyWater runs down. Every upper layer must sit on top of the layer below it, like shingles on a roof.

Chapter 2 of 7

Every window on the South Coast.

Style, frame material and glass all change performance and price.

Steel and wood

Steel casements, thin and crisp, are original to many 1920s Spanish Colonial Revival houses. Wood windows, painted or clad in aluminum outside, suit Craftsman and traditional houses.

WhyOriginal steel windows can often be restored and fitted with better seals instead of replaced.

Aluminum, vinyl and fiberglass

Single-pane aluminum sliders were standard from the 1950s to the 1980s. Vinyl replaced them in many retrofits. Fiberglass is stiff, stable and paintable.

The glass

Today’s insulated glass is two panes with a sealed space between them and a low-emissivity coating that reflects heat. In a fire hazard zone, at least one pane is tempered.

WhyLow-E glass keeps summer heat out and winter heat in. It is why a new house can have big glass and still meet the energy code.

Chapter 3 of 7

From sand to an insulated glass unit.

Almost all window glass is float glass: molten glass poured onto a bath of molten tin.

From batch to unit

Sand, soda ash and limestone are melted, floated flat on molten tin, cooled slowly, coated, cut and assembled into sealed units.

The float bath

Molten glass spreads across a bath of liquid tin and settles perfectly flat and parallel, then cools enough to roll out.

WhyBefore float glass, window glass was rolled or blown and had waves you can still see in old houses.

Coat and seal

A microscopically thin metallic low-E coating is applied, then two panes are sealed around a spacer, often with argon gas between them.

Chapter 4 of 7

Installed right: the order of the layers.

The order of operations is the whole craft.

Pan, set, flash

Pan the sill, set the window plumb and square on shims, fasten it to the maker’s schedule, then tape the side fins and flash the head.

Leave the bottom open

The bottom fin is never sealed tight to the pan; water that reaches the pan has to drain out.

WhyA sealed bottom turns a sill pan into a bathtub inside the wall.

Test it

On important openings we water-test before the siding or stucco goes on: a spray rack or hose at the head, while someone watches inside.

Chapter 5 of 7

A hundred years of South Coast windows.

Window technology changed more than almost anything else in a house.

1920s: steel casements

Slim steel casements with small panes defined Spanish Colonial Revival houses. Single glazed, with putty, they leak air but last when painted.

1930s to 1950s: wood sash

Wood double-hung and casement windows, often with wavy glass, in Craftsman and Colonial houses.

1960s: the aluminum slider

Mill-finish aluminum sliders went into tracts and many remodels. They conduct heat and cold straight through.

1978: the energy code

California’s first Title 24 energy standards took effect in 1978 and began pushing toward double glazing.

2008: fire-rated openings

In fire hazard zones, Chapter 7A required tempered glass in at least one pane, plus fire-resistant exterior doors.

Today

Low-E dual glazing, thermally broken frames, large lift-and-slide doors, and installations tested for water before they are covered.

Chapter 6 of 7

The same trade, on a real ADU.

Every course ends on one building: a 710-square-foot ADU on Canon Drive in the Santa Barbara foothills, modelled from its permit set before pricing. Three gables, three floor levels, a steel canopy, and a list of questions the drawings left open. Here are sixteen openings and the questions they raised.

Bronze aluminum, tempered glass

Frames are bronze anodized aluminum by Western Windows: Series 8670 windows and Series 7000 and 300 sliding doors. Because the lot is in the high fire area, every exterior window and glazed door is ordered with at least one tempered pane; the glazing notes cited an old code section and we flagged it.

The escape window, an inch short on paper

The bedroom has no exterior door, so window 103-A is its emergency escape opening. The code needs a clear opening at least 20 inches wide and 5.7 square feet. The casement in the first set is about 1'-10" wide, which leaves about 19 inches clear: one inch short.

WhyWidening the casement to 2 feet fixes it without changing the rough opening. Submittal 3 now states 6.26 square feet clear, and the shop drawing has to show it.

Sill pans and a weather barrier

Every opening gets a sloped sill pan and is lapped into the weather barrier so water that gets behind the cladding runs out, not in. The marine climate also calls for a 3/16-inch drainage gap behind the cladding.

A pivot and two sliders

Door 100-2 is 9'-7" wide: one panel pivots on an offset axis at the west end and two panels slide. The pivot swings into the living room, so the dining table has to clear it.

Chapter 7 of 7

What it means for your windows.

Window work is where design review, the energy code and the fire code meet.

Repair, replace or retrofit

Original steel and wood windows can often be restored. Replacement is either a full frame, opened to the studs and flashed properly, or an insert into the old frame.

WhyAn insert is quicker and cheaper; full-frame replacement is the only way to fix a leaking opening.

A way out of every bedroom

Every bedroom needs an emergency escape opening: a window or door that opens to at least 5.7 square feet of clear space, at least 20 inches wide and 24 inches high, with the sill no more than 44 inches above the floor. Replacement windows in old bedrooms are sized to keep or improve that opening.

WhyA smaller replacement window, or bars that do not open from inside, can turn a bedroom into a trap in a fire. Check the clear opening, not the window size.

Restoring steel windows

Original steel casements can usually be saved. The sash comes out, is stripped to bare steel, rust at the bottom rail is cut out or filled, and it is primed, reglazed with new putty or glazing tape, fitted with weatherstripping and painted. Hinges and operators are freed or replaced. Thin new insulated glass can sometimes fit the old frames.

WhyRestored originals keep the thin profile that replacement windows rarely match, and design review on historic houses often asks to keep them.

Design review counts muntins

On the South Coast, design review often cares about the pattern of the glass, the depth of the frame and the color. True divided lites or simulated divided lites with bars on both faces read like the originals; grilles sealed between the glass look flat from the street. Bring photos of the originals.

Doors and fire

In a fire hazard zone, exterior doors must be noncombustible, fire-rated, or solid-core wood of a minimum thickness, and glass must be tempered.

Big sliding and pocket doors

Wide openings to a terrace are often multi-slide doors: several glass panels that slide and stack, sometimes into a pocket inside the wall. The opening needs a long header or steel beam sized by the engineer, and the sill track is set flush in a pan that drains to outside so indoor and outdoor floors can meet at one level.

WhyA flush threshold invites water. The drained pan, a slight slope outside and a covered overhang are what keep it dry.

Exterior doors: the sill pan

Doors leak at the bottom. A pan with end dams and a back leg goes under every exterior door, the threshold is set in sealant along the back so water that gets in can drain out the front, and the outside surface steps down and slopes away.

WhyPatio doors facing the weather on the coast are the most common source of rotted subfloor we open up.

Safety glass and where it goes

Ordinary annealed glass breaks into sharp shards. The code calls for safety glass where people can fall or push into it: in doors, beside doors, near tubs and showers, near stairs and low to the floor. Tempered glass crumbles into small cubes; laminated glass has a plastic layer that holds the pieces. Most new windows are insulated units, two panes and a spacer with a low-E coating.

WhyEvery tempered pane carries a small etched mark in a corner. If a replacement pane in a door has none, it is not safety glass.

Garage doors

A sectional door rolls up on tracks, balanced by a torsion spring above the opening. The opener lifts it, photo eyes near the floor stop and reverse it, and in California a new opener must have a battery backup so the door works in a power outage.

WhyThe spring holds the whole weight of the door. Adjusting or replacing it is a job for a garage door technician, not the homeowner.

Santa Barbara: Carriage-style wood doors that swing or look like they swing are common on Spanish Colonial Revival garages, and design review often asks for them.

Pivot doors

A big front door that turns on a pivot rather than hinges can be very wide and heavy. The bottom pivot sits in the floor, so its pocket is blocked out before the slab is poured or the subfloor is laid, and its top pivot needs solid framing above. Because the door swings past the sill, water management at the threshold has to be designed: a sill pan, a slope away and a drained threshold.

WhyA pivot door is decided at foundation time, not at trim. The pocket is the expensive thing to add later.

Hidden screens for big openings

Wide lift-and-slide and folding doors have no room for an ordinary screen. Retractable screens roll into a housing above the opening, by hand or by motor, and run in side tracks that hold them flat in the wind. The housing is recessed into the header so it disappears, which means the framer and the window supplier have to agree on its size before the header is built.

WhyA screen pocket added after the header is built usually ends up as a box hanging below it.

Setting big glass

The large fixed panes and sliding panels on high-end houses can weigh hundreds of pounds each. They are set with vacuum lifters on a crane, a glazing robot or a mini-crane, never by hand, and the access route is planned with the schedule. Each unit rests on rubber setting blocks near its quarter points so its weight bears evenly and the glass never touches metal, and the frame below it drains to the outside.

WhyAsk the supplier for unit weights before the site plan is fixed. A pane that cannot be reached by a lifter cannot be installed.

Install it the way it was tested

A window's air, water and structural ratings were earned in a test lab, installed a specific way. Its warranty depends on the same. So the installer works from the manufacturer's printed instructions: the rough opening size, where shims go, which fasteners, how far apart and how far from the corners, what sealant and in what order. Shims go at the fastener points on the jambs, never jammed at the head, and the unit is checked for plumb, level, square and smooth operation before anything is foamed or trimmed.

WhyA window installed off the instructions can lose its rating and its warranty. Keep the sheet on site and follow it.

Read the window label

Every window sold in California carries an NFRC label with its ratings. The U-factor is how fast heat passes through the whole unit: lower is better. The solar heat gain coefficient is how much of the sun's heat it lets in: lower for west glass that bakes in the afternoon, higher where winter sun is welcome. Insulated glass, a low-e coating and a warm-edge spacer keep the inside pane warmer, which is also why good windows fog less: condensation forms on the coldest surface in the room.

WhyThe energy code holds the window to the numbers in the energy report. Check the label against it at delivery, before the units go in.

Adjusting a door

Most doors that stick, rattle or leak air need adjustment, not replacement. A door that drags at the top of the latch side has usually sagged on its hinges: tightening the screws, or driving one long screw through the top hinge into the framing, pulls it back. The strike is moved so the latch catches without slamming, and the weatherstripping and door sweep are adjusted until no daylight shows around the closed door.

WhyLook for daylight from inside with the door closed. Wherever light shows, air and wind-driven rain get in.

After the film

Use it on a real house.

On your house

We install windows the slow way: pan, set, flash, test. It is the cheapest insurance against a rotted wall.

For our crew

The AMN crew trains on the full private set for this trade: a 3D job site you walk station by station, the lesson plan, the field guide, the math and the tools. Sign-in is not needed, but these pages are kept out of search.

Trades in this course

  • Windows and doors installation · C-17
  • Glazing and glass · C-17
  • Steel windows and doors
  • Garage doors

All 100 trades

Before you hire

In California, a license is needed for any job of $1,000 or more in labor and materials, any job that needs a permit, or any job where the worker hires help. Look up the contractor’s license number at cslb.ca.gov and check it is active and carries the right class:

  • Windows and doors installation: CSLB class C-17

On the job: the install checklist.

The install chapter as a list to walk before you call the work done. Ticks stay in this browser only. Prints on one page.

Windows, doors and weatherproofing · Job: ________________ · Date: __________ · Checked by: ________________

Check yourself. Out loud.

The same drill our crew uses: give the answer in two sentences before you open each one. If you can only name the thing, read that chapter again.

01 The sill pan comes firstSay why it matters, then open

Every window leaks a little eventually. The pan catches that water and sends it back outside.

From chapter: An opening, layer by layer

02 The glassSay why it matters, then open

Low-E glass keeps summer heat out and winter heat in. It is why a new house can have big glass and still meet the energy code.

From chapter: Windows and doors

03 The escape window, an inch short on paperSay why it matters, then open

Widening the casement to 2 feet fixes it without changing the rough opening. Submittal 3 now states 6.26 square feet clear, and the shop drawing has to show it.

From chapter: A real ADU

04 Big sliding and pocket doorsSay why it matters, then open

A flush threshold invites water. The drained pan, a slight slope outside and a covered overhang are what keep it dry.

From chapter: Your house

05 Garage doorsSay why it matters, then open

The spring holds the whole weight of the door. Adjusting or replacing it is a job for a garage door technician, not the homeowner.

From chapter: Your house

06 Setting big glassSay why it matters, then open

Ask the supplier for unit weights before the site plan is fixed. A pane that cannot be reached by a lifter cannot be installed.

From chapter: Your house

Words in this course.

18 terms in plain English, with the Spanish our crew uses. All 249 words across the school are on one page.

Axis Eje
An imaginary straight line that rooms or gardens line up on.
Casement Abatible
A window that swings open on side hinges, like a door.
Divided lites Vidrios divididos
A window made of small panes. True ones are separate panes; simulated ones are bars stuck on one big pane.
Flashing Tapajuntas
Thin metal or membrane that steers water away from a joint, such as around a window.
Jamb Jamba
The frame a door or window sits in.
Muntin Barrote
A thin bar between panes of glass in one window.
Pivot door Puerta pivotante
A door that turns on a point in the floor and head, not on hinges.
Pocket door Puerta corrediza oculta
A door that slides into a slot inside the wall.
Profile Perfil
The outline of a molding if you slice through it.
Sash Hoja
The part of a window that holds the glass and moves.
Section Sección
A drawing of a building or part as if sliced through.
Setting block Calza de apoyo
A rubber block a pane of glass rests on inside its frame.
Sill pan Charola de alféizar
A waterproof tray under a window that sends leaks back outside.
Solar heat gain coefficient Coeficiente de ganancia de calor solar
How much of the sun's heat a window lets in.
Spanish Colonial Revival Spanish Colonial Revival
The white-plaster, red-tile style that defines Santa Barbara, built mostly 1915 to 1930.
Stud Montante
One of the upright framing pieces inside a wall.
Threshold Umbral
The strip under a door. Also the moment of passing from one space into another.
U-factor Factor U
How fast heat passes through a whole window; lower is better.

Questions people ask.

Should I replace or restore my old steel windows?

Often restore. Original steel casements on Spanish Colonial Revival houses can be stripped, repaired, reglazed and weatherstripped. Replacement makes sense when frames are badly rusted or the energy goals require it.

What is a sill pan?

A sloped tray of flashing at the bottom of a window or door opening that catches any water that gets past the window and directs it back outside.

What windows are required in a fire hazard zone in California?

In wildland-urban interface areas, windows need insulated glass with at least one tempered pane, or a fire-rated assembly. Exterior doors have their own requirements.

Do I need design review to replace windows in Santa Barbara?

Sometimes. In historic districts, for landmarks and for visible changes in Montecito, window changes may go to design review. We check the parcel first.

What has to be planned for a pivot front door?

The floor pivot. Its pocket is blocked out before the slab is poured or the subfloor is laid, the top pivot needs solid framing above, and the threshold needs a sill pan and a drained sill because the door swings past it.

Sources and checks

Rules change with each code cycle, and the plans, the inspector, the adopted code and the maker’s instructions overrule any course. Code references are to the 2025 California Building Standards Code (Title 24), in force since 1 January 2026; check the local amendments of the city or county. This page was checked against these on 18 November 2026:

  • California Residential Code R703.4 (flashing at openings), R703.2 (water-resistive barrier), R308 (safety glazing), R337.8 (exterior windows and doors in wildfire areas)
  • ASTM E2112, standard practice for installation of exterior windows, doors and skylights
  • California Energy Commission, Title 24 Part 6 (first energy standards 1978; current 2025 code effective 1 January 2026)
  • Glass Association of North America, float glass and insulating glass manufacture
  • AMN crew field guide: Windows, doors and weatherproofing
  • National Fenestration Rating Council (NFRC) label: U-factor and solar heat gain coefficient

Ask about your house

Matt Newman · 805 886 0988 · purchasing@amnbuild.com