AMN Construction
AMN Construction · Trade School · Solar, batteries and EV

Trade School · course 17 of 28 · new trade

Solar, batteries and EV. The house as a small power plant.

A California house built today makes some of its own electricity, may store it, and probably charges a car. This course opens a solar panel cell by cell, follows silicon from sand to module, shows how panels, inverters, batteries and chargers connect to the panel, and walks the rules from the first rooftop systems to net billing.

7 chapters30 3D scenes10 min readSanta Barbara South CoastChecked 19 Nov 2026

The 3D scenes need WebGL, which this browser has turned off. Every word of the course is still here on the left.

Chapter 1 of 7

Inside a solar panel.

A solar panel is a sandwich built to survive thirty years of sun, rain and salt air.

A sandwich

From the back: a protective backsheet, a clear encapsulant, a layer of silicon cells, more encapsulant, tempered glass, and an aluminum frame around the edge.

Cells

Each cell is a thin silicon wafer. Light knocks electrons loose; the cell’s layers push them one way, making direct current. Cells are wired in strings to build up voltage.

WhyShade on a few cells can drag down a whole string, which is why panel layout and optimizers matter.

Glass and frame

Tempered glass takes hail and heat; the frame bolts to the racking and is grounded.

Chapter 2 of 7

Panels, inverters, batteries and chargers.

A home system is more than panels on the roof.

Inverters

Panels make direct current; the house uses alternating current. Microinverters convert at each panel; a string inverter converts for many panels at once, sometimes with optimizers at each panel.

Rapid shutdown

The electrical code requires rooftop solar to de-energize quickly when the system is shut down, so firefighters are not facing live conductors on the roof.

Batteries

Lithium iron phosphate (LFP) batteries store midday solar for evening use and keep chosen circuits running in an outage. They are installed to fire and electrical rules on location and clearances.

The panel and the charger

Everything lands at the main electrical panel, which may need upgrading. A Level 2 EV charger runs on a dedicated 240-volt circuit.

Chapter 3 of 7

From quartz sand to a framed module.

Solar-grade silicon is purified to extraordinary levels before it is sliced into wafers.

Seven stations

Quartz is refined into ultra-pure polysilicon, melted and grown into ingots, sliced into wafers thinner than a fingernail, made into cells, laminated into modules and tested under a flash of simulated sunlight.

The flash test

Each finished module is flashed with a calibrated light and its output measured; that is where the wattage on the label comes from.

Chapter 4 of 7

Installed right: roof, rails, rules.

The roof is the part that has to outlast the panels.

Flash every attachment

Every bolt through the roof gets a flashed mount designed for that roof type. On clay tile, tiles are replaced with flashed tile hooks or flat replacement tiles.

WhyA leaking solar attachment can rot a rafter for years before a stain shows.

Fire setbacks

Fire code pathways keep clear strips at ridges and edges so firefighters can work on the roof.

Permit, inspect, interconnect

Systems are permitted and inspected by the City or County, then approved for interconnection by Southern California Edison before they are turned on.

Chapter 5 of 7

Fifty years of California solar.

Solar went from experiment to code requirement within one working lifetime.

1970s: solar water heating

The energy crises of the 1970s brought rooftop solar water heaters and the first state incentives.

2000s: rooftop PV

Falling panel prices and state programs put photovoltaic systems on many homes.

2020: the solar mandate

From 1 January 2020, California’s energy code required solar on most new single-family homes.

2023: net billing

In April 2023 new customers of the large utilities, including Southern California Edison, moved to net billing, which pays less for exported power and makes batteries more valuable.

Today

The 2025 Energy Code adds battery-ready requirements for new homes; solar, storage and EV charging are planned with the electrical service from the start.

Chapter 6 of 7

The same trade, on a real ADU.

Every course ends on one building: a 710-square-foot ADU on Canon Drive in the Santa Barbara foothills, modelled from its permit set before pricing. Three gables, three floor levels, a steel canopy, and a list of questions the drawings left open. Here is how the energy code reaches a new ADU.

A new detached ADU needs solar

Under the Energy Code a new detached ADU counts as a newly constructed building, so it carries the solar requirement unless an exception applies. The energy report came with Submittal 3, and the system is sized from it.

Or add panels to the main house

Under the 2022 code, new modules added to an existing system on the same lot can meet the ADU's requirement. On this lot the west-facing slope of the primary gable is one place panels could go; the main house roof may be better.

All electric already

With heat pumps for heating, cooling and hot water and an electric range, the ADU has no gas line at all. The panel and the feeder are sized for that from the start.

Chapter 7 of 7

What it means for your house.

Solar is a roof project and an electrical project at once.

Roof first

If the roof is near the end of its life, re-roof before solar goes on; removing and reinstalling panels later is expensive.

Solar on a tile roof

On clay or concrete tile, panels mount to tile hooks: a tile is lifted, the hook is screwed into a rafter and flashed to the deck, and the tile is notched or replaced with a flashed mount so it sits back down around the hook. Rails ride above the tile. No hole goes through a tile face.

WhyMost solar roof leaks on tile come from broken tiles or unflashed hooks. Spare matching tiles are set aside before work starts.

Panel capacity

Solar, a battery and an EV charger all connect at the main panel, which on older houses may need an upgrade coordinated with Edison. The Cannon Drive ADU takes its power as a feeder from the main house; the feeder route and panel size are still open questions on its plans. The Cannon Drive ADU's plans carry solar, and the 2025 Energy Code adds battery readiness for new homes.

Where a battery can go

Home batteries go in a garage, on an outside wall or in a utility room, not in bedrooms or living spaces. The fire code limits how much storage goes in one spot, keeps units a set distance from doors and windows, and asks for protection where cars could hit them. A gateway and disconnect sit nearby.

WhyClearances can decide whether a battery fits at all on a narrow side yard. Check the spot before the battery is ordered.

Backup power

When the grid goes down, as it does in South Coast fire weather shutoffs, a house can run on a standby generator or a battery. Either one feeds a critical-loads panel through a transfer switch or gateway that keeps the house from back-feeding the utility lines. A generator sits on a pad, clear of windows and doors because of exhaust; a battery switches over in a fraction of a second.

WhyBack-feeding through a cord plugged into a dryer outlet can electrocute a lineworker. A listed transfer switch, installed under permit, is the only safe way.

Design review

Visible panels, especially on historic houses or in design-review areas, may need placement or color choices that keep the roofline quiet.

Solar on a standing-seam roof

A standing-seam metal roof is the easiest roof to put solar on without a single hole. Clamps made for the seam profile grip the raised seams with set screws; rails or the panels themselves fasten to the clamps, and everything is bonded to ground. The clamp must match the seam shape and the metal: copper and zinc roofs need compatible clamp material, and the panel layout still keeps the fire department's roof pathways clear.

WhyChoosing a seamed metal roof and solar together saves the flashing at every attachment, the place tile and shingle solar most often leaks.

Shade is the enemy

Solar panels in a string share current, so a panel in shade, from a chimney, a vent stack or a tree, can pull down the output of every panel wired with it. Module-level electronics, optimizers or microinverters, limit the loss to the shaded panel. The design starts with a shade study across the whole year, accounting for trees that will grow, and panels are kept out of the shadow of chimneys and parapets entirely where possible.

WhyAn eight-foot oak today is a twenty-foot oak in ten years. Put trees in the shade study.

Wait for permission to operate

A solar system that passes the building inspection is not yet allowed to run. The utility has to approve the interconnection and issue permission to operate, and turning a grid-tied system on before that can break the interconnection agreement. After it is on, the monitoring is the warranty's early-warning system: a string that produces less than its neighbors, an inverter that drops offline. Someone should look at the first month of data and set alerts.

WhyOwners switch systems on early because the panels look finished. Tell them, in writing, to wait for the utility's notice.

Santa Barbara: On the South Coast interconnection is with Southern California Edison.

Sizing an EV circuit

Car charging is a continuous load, running for hours at full current, so the electrical code sizes its circuit at 125 percent of what the charger draws: a charger set for 32 amps needs a 40-amp circuit, a 48-amp charger a 60-amp circuit. Many chargers can be set lower, and load-management devices can share capacity with the rest of the house, which can avoid a service upgrade. The load calculation decides which.

WhyInstall the circuit for the car the owner will have in five years, but set the charger to what the panel can carry today.

After the film

Use it on a real house.

On your house

We plan solar, storage and charging with the roof and the electrical service, so the pieces fit the first time.

For our crew

Solar and storage are new to the school. The electrical job site covers the panel, grounding and circuits every system connects to.

Trades in this course

  • Generators and backup power · C-10
  • Solar · C-46
  • Battery storage · C-10
  • EV charging · C-10

All 100 trades

Before you hire

In California, a license is needed for any job of $1,000 or more in labor and materials, any job that needs a permit, or any job where the worker hires help. Look up the contractor’s license number at cslb.ca.gov and check it is active and carries the right class:

  • Generators and backup power: CSLB class C-10
  • Solar: CSLB class C-46

On the job: the install checklist.

The install chapter as a list to walk before you call the work done. Ticks stay in this browser only. Prints on one page.

Solar, batteries and EV · Job: ________________ · Date: __________ · Checked by: ________________

Check yourself. Out loud.

The same drill our crew uses: give the answer in two sentences before you open each one. If you can only name the thing, read that chapter again.

01 CellsSay why it matters, then open

Shade on a few cells can drag down a whole string, which is why panel layout and optimizers matter.

From chapter: Inside a panel

02 Flash every attachmentSay why it matters, then open

A leaking solar attachment can rot a rafter for years before a stain shows.

From chapter: Installed right

03 Where a battery can goSay why it matters, then open

Clearances can decide whether a battery fits at all on a narrow side yard. Check the spot before the battery is ordered.

From chapter: Your house

04 Backup powerSay why it matters, then open

Back-feeding through a cord plugged into a dryer outlet can electrocute a lineworker. A listed transfer switch, installed under permit, is the only safe way.

From chapter: Your house

05 Shade is the enemySay why it matters, then open

An eight-foot oak today is a twenty-foot oak in ten years. Put trees in the shade study.

From chapter: Your house

06 Wait for permission to operateSay why it matters, then open

Owners switch systems on early because the panels look finished. Tell them, in writing, to wait for the utility's notice.

From chapter: Your house

Words in this course.

9 terms in plain English, with the Spanish our crew uses. All 249 words across the school are on one page.

Fire access pathway Pasillo de acceso para bomberos
The clear strip left on a roof around solar panels so firefighters can walk and vent the roof.
Flashing Tapajuntas
Thin metal or membrane that steers water away from a joint, such as around a window.
Gable Hastial
The triangle of wall under the two slopes of a roof.
Heat pump Bomba de calor
An electric machine that both heats and cools a house by moving heat, not making it.
Parapet Pretil
A low wall that sticks up above the edge of a roof.
Permission to operate Permiso para operar
The utility's approval to switch on a grid-tied solar system.
Profile Perfil
The outline of a molding if you slice through it.
Rafter Cabio
A sloped beam that holds up the roof.
Ridge Cumbrera
The top line of a roof.

Questions people ask.

Is solar required on new homes in California?

Yes, for most new single-family homes since 1 January 2020, with exceptions. The 2025 Energy Code also adds battery-ready requirements.

Is a home battery worth it in Santa Barbara?

Since net billing began in April 2023, exported solar earns less, so storing it for evening use is worth more, and a battery also provides backup in outages. The numbers depend on your use and your rate.

Can solar go on a clay tile roof?

Yes, with tile-specific flashed mounts or replacement flat tiles. It takes a careful installer; broken tiles and poorly flashed hooks are common leak sources.

Do I need a panel upgrade for an EV charger?

Sometimes. A load calculation shows whether the existing service can support a Level 2 charger; load-management devices can avoid an upgrade.

Can I turn my solar system on after the city inspection?

Not until the utility issues permission to operate. On the South Coast that is Southern California Edison.

Can solar go on a standing-seam metal roof without holes?

Yes. Clamps made for the seam profile grip the raised seams, and the rails or panels fasten to the clamps, so nothing penetrates the roof. The clamp has to match the seam shape and the metal.

Sources and checks

Rules change with each code cycle, and the plans, the inspector, the adopted code and the maker’s instructions overrule any course. Code references are to the 2025 California Building Standards Code (Title 24), in force since 1 January 2026; check the local amendments of the city or county. This page was checked against these on 18 November 2026:

  • California Energy Commission, 2019 Energy Code solar requirement for new single-family homes (effective 1 January 2020) and 2025 Energy Code battery-ready requirements
  • California Public Utilities Commission, Net Billing Tariff (effective April 2023 for SCE, PG&E and SDG&E customers)
  • NFPA 70 (NEC) Article 690 (PV systems, 690.12 rapid shutdown), 705 (interconnection), 706 (energy storage), 625 (EV charging)
  • California Fire Code 1205 (solar roof access pathways)
  • Southern California Edison interconnection requirements

Ask about your house

Matt Newman · 805 886 0988 · purchasing@amnbuild.com