AMN Construction

Trade School · course 08 of 28

Framing. The skeleton, and how it holds in an earthquake.

Almost every house on the South Coast is a wood frame. This course takes a wall apart stud by stud, follows a Douglas fir log through the mill, shows how a frame is made to survive an earthquake, and walks a hundred years of framing from balloon frames to engineered shear walls.

7 chapters32 3D scenes10 min readSanta Barbara South CoastChecked 19 Nov 2026

The 3D scenes need WebGL, which this browser has turned off. Every word of the course is still here on the left.

Chapter 1 of 7

Inside a framed wall.

A framed wall is a ladder of studs between two plates, wrapped in panels that make it stiff.

Plates and studs

A wall starts as a bottom plate, a row of studs and a doubled top plate. Studs are usually 16 inches apart, measured center to center, so 4-by-8 sheets land on a stud at every edge.

WhySixteen inches is a module: plywood, drywall and insulation are all sized to it.

Sheathing makes it stiff

A frame of studs alone racks like a parallelogram. Nailing plywood or OSB panels to it turns it into a stiff diaphragm that resists sideways force from wind and earthquakes.

Nails are the structure

In a shear wall the nails do the work. The plans set the nail size and the spacing at panel edges, often 4 inches or closer, and the inspector checks it before the wall is covered.

WhyAn overdriven nail that breaks the plywood face, or one that misses the stud, is a nail that is not there.

Chapter 2 of 7

The lumber yard, and the steel that ties it.

Framers work with sawn lumber, engineered wood and a catalog of steel connectors.

Sawn lumber and the grade stamp

On the South Coast most framing lumber is Douglas fir. Each piece carries a stamp: species, grade, mill, and whether it was kiln-dried. A "2x4" is actually 1-1/2 by 3-1/2 inches once dried and planed.

WhyThe grade sets how much load the piece may carry. The engineer designs to the grade, so the stamp matters.

Engineered wood

LVL beams, I-joists and glulams are made from veneers, strands or boards glued under pressure. They are straight, consistent and can span farther than sawn lumber of the same depth.

Steel connectors

Hold-downs anchor the ends of shear walls to the foundation; hangers, straps and ties carry loads across joints. On the coast they are specified hot-dip galvanized or stainless steel.

WhySalt air corrodes thin galvanizing, and pressure-treated wood corrodes plain steel.

Chapter 3 of 7

From a fir log to a stamped stud.

A sawmill turns a round log into square lumber, then dries and grades every piece.

Seven stations

Logs are harvested, squared on the head rig, edged and trimmed, kiln-dried, planed smooth, graded and stamped, then bundled for the yard.

Kiln drying

Green lumber can be more than a third water by weight. Kiln drying brings it down, commonly to 19 percent or less, stamped KD or S-DRY.

WhyWood shrinks as it dries. Framing with wet lumber means nail pops, cracked plaster and squeaky floors later.

Grading

Each piece is graded by eye or by machine for knots, slope of grain and wane, and stamped with its grade.

Chapter 4 of 7

Framed right: load paths and shear walls.

Good framing is a continuous path from the roof to the foundation, for gravity and for earthquakes.

Gravity: headers carry openings

Over every door and window a header carries the load from above to the jack studs at each side, and down to the foundation.

Sideways: shear walls and hold-downs

Designated shear walls are sheathed and nailed to a schedule. At their ends, hold-downs bolt to the foundation so the wall cannot tip up in an earthquake.

WhyAn earthquake pushes the top of a wall sideways. Without a hold-down, the end of the wall lifts and the wall rotates instead of resisting.

Frame inspection

Before insulation, the inspector walks the frame: nailing, hold-downs, straps, headers, fireblocking and the plumbing and wiring holes drilled through it.

Chapter 5 of 7

A hundred years of framing here.

South Coast framing tracks two stories: the lumber got smaller and straighter, and the earthquake rules got stronger.

1920s: balloon and early platform frames

Older houses used rough-sawn lumber, often a true 2 by 4 inches, and some used balloon framing, with studs running two stories and open channels from crawlspace to attic.

WhyThose open channels act like chimneys in a fire. Modern code requires fireblocking to close them.

1940s: platform framing

Each floor is framed as a platform and the next walls stand on it. It is how almost everything is built today.

1960s: dried, planed and drywalled

Lumber shrank to today’s dimensions as kiln drying and planing became standard, and drywall replaced lath and plaster.

1971 and 1994: the earthquake lessons

After San Fernando (1971) and Northridge (1994), engineered shear walls, hold-downs and tighter nailing schedules became standard.

Today

Engineered beams, I-joists, prescribed shear nailing, continuous load paths and corrosion-resistant connectors near the ocean.

Chapter 6 of 7

The same trade, on a real ADU.

Every course ends on one building: a 710-square-foot ADU on Canon Drive in the Santa Barbara foothills, modelled from its permit set before pricing. Three gables, three floor levels, a steel canopy, and a list of questions the drawings left open. Here is the frame, from sill plate to ridge.

2x6 walls at 16 inches

Exterior walls are 2x6 at 16 inches on center with R-20 insulation, and several of them add a 2x4 layer inside the 2x6. Interior walls are 2x4, except the 2x6 walls between the kitchen and the bedroom and between the bath and the bedroom.

Blocking decided before drywall

Grab-bar blocking at every toilet and shower (the City asked for it), cabinet backing, the range hood, the TV and the three ductless heads. Every wall-hung item needs wood behind the drywall, and the owner has to decide where before insulation.

WhyBlocking costs minutes during framing and a wall repair after.

Shear walls and sheathing

Sheathing on the exterior walls makes them shear walls. Submittal 3's structural sheets give the details: 15/32-inch sheathing, HDUE3 hold-downs at each end of nine shear walls, and 5/8-inch anchor bolts at 48 inches.

Ridges, valleys and the step at grid C

The roof frame hangs rafters from three ridge beams, with an LVL beam over the bath wall on grid C and 4x6 headers over the hall openings, with a step in the roof at grid C where the primary gable sits a foot higher than the bedroom gable. Rafter tails are notched for the gutters.

Chapter 7 of 7

What it means for your house.

Framing decides what you can move. These are the questions behind most remodel plans.

Can that wall come out?

A bearing wall carries a floor or roof. Removing it means a beam, posts and sometimes new footings below, designed by an engineer. Non-bearing walls are much simpler.

Where you may cut a joist

Plumbers and electricians have to get through floor framing. In sawn joists, holes go in the middle third of the depth and away from the ends, and the bottom edge is never notched in the middle of the span. Engineered I-joists have a maker's chart of allowed hole sizes and spots, and their flanges are never cut.

WhyA cut flange or a notch in the wrong place can drop a floor's strength by half. If it happens, the engineer specifies the repair.

Fire blocking

A fire that gets into a hollow wall can race up it to the attic. Fire blocking stops that: solid wood or other approved material closes every wall cavity at each floor and ceiling line, at soffits and along stair stringers, and every pipe or wire hole through it is sealed with fire-rated sealant.

WhyOld balloon-framed houses have studs running two stories with no blocking at all. Adding it is part of any remodel that opens those walls.

Taking out a bearing wall

Before a bearing wall comes out, temporary shoring walls hold up the floor or roof. Then the wall is removed, new footings go in where the posts will land, the engineer's beam (LVL, glulam or steel) is set on posts, connected at both ends, and the shoring comes out. The inspector sees the footings and connections before they are covered.

WhyThe beam is the easy part. The load still has to reach the ground, which is why new footings so often appear under the posts.

Older frames are not wrong, just different

Rough-sawn old studs are often larger than new ones, which makes matching them in a remodel a carpentry job of its own.

The roof frame

Additions and second stories tie new framing to old. Rafters sit on the wall plates, ceiling joists tie the walls so the roof cannot spread, and hurricane ties hold each rafter down. On an older house we check rafter size, spacing and sag before plans are drawn.

Deck ledgers

A deck that hangs on a house hangs on its ledger: a pressure-treated board through-bolted or lag-screwed into the house framing in a staggered pattern, with membrane behind it and flashing lapped over it and behind the paper above, and joists in galvanized hangers. Nails alone are not allowed.

WhyLedger failure is the most common cause of deck collapse, and it starts with water rotting the rim behind an unflashed ledger.

Floor framing

A wood floor is joists set on edge across the house, usually 16 inches apart and crown up, tied at the ends by a rim joist and bearing on sills or beams. Blocking between joists keeps them from rolling, hangers carry joists that meet a beam, and the subfloor is glued and screwed to stop squeaks.

WhyA bouncy or squeaky floor in an older house is usually undersized or unblocked joists. Adding blocking and sistering joists from below fixes most of it before new floors go down.

Crown up, layout from one end

Almost every joist and rafter has a slight bow along its length. The framer sights down each one and sets it with the bow, the crown, facing up, so the load flattens it instead of making the sag worse. Layout is pulled from one end of the wall or floor and marked every 16 inches, so the edges of 4-by-8 sheets land on the center of a framing member at 48 inches. Get the layout right and every sheet of plywood and drywall that follows has something to nail to.

WhyA floor with crowns mixed up and down squeaks and shows in the finish floor. It takes a second per board to get it right.

Dry and straight before close-in

Framing lumber gets wet in the rain and is sometimes delivered wet. Closed in damp, it shrinks after the drywall is up: nails pop, corners crack and doors bind. California's green building code asks that wall and floor framing be checked with a moisture meter before it is enclosed, at 19 percent moisture content or less. The same week the framer straightens walls: a string line along each long wall, studs that bow too far planed or replaced, so the drywall and the cabinets go onto something straight.

WhyThe frame is the last chance to fix straightness cheaply. After drywall it costs ten times more and shows in every cabinet and tile line.

Fill every hanger hole

A joist hanger is only as strong as its fasteners. Its load rating assumes the specific nails the maker lists, in every hole the instructions call for, including the angled holes through the joist. Drywall screws snap under shear, many deck screws are not rated for it, and short nails pull out. Inspectors look at hangers closely, and a missing nail pattern is a common correction on a framing inspection.

WhyCheck the hanger's catalog page on site: nail size, count and which holes. Then fill them all.

After the film

Use it on a real house.

On your house

Framing is where a remodel’s layout is decided. We open the plans with an engineer before anyone promises an open kitchen.

For our crew

The AMN crew trains on the full private set for this trade: a 3D job site you walk station by station, the lesson plan, the field guide, the math and the tools. Sign-in is not needed, but these pages are kept out of search.

Trades in this course

  • Framing and rough carpentry · C-5
  • Seismic retrofit

All 100 trades

Before you hire

In California, a license is needed for any job of $1,000 or more in labor and materials, any job that needs a permit, or any job where the worker hires help. Look up the contractor’s license number at cslb.ca.gov and check it is active and carries the right class:

  • Framing and rough carpentry: CSLB class C-5

On the job: the install checklist.

The install chapter as a list to walk before you call the work done. Ticks stay in this browser only. Prints on one page.

Framing · Job: ________________ · Date: __________ · Checked by: ________________

Check yourself. Out loud.

The same drill our crew uses: give the answer in two sentences before you open each one. If you can only name the thing, read that chapter again.

01 Plates and studsSay why it matters, then open

Sixteen inches is a module: plywood, drywall and insulation are all sized to it.

From chapter: Inside a wall

02 Sawn lumber and the grade stampSay why it matters, then open

The grade sets how much load the piece may carry. The engineer designs to the grade, so the stamp matters.

From chapter: Lumber and hardware

03 Sideways: shear walls and hold-downsSay why it matters, then open

An earthquake pushes the top of a wall sideways. Without a hold-down, the end of the wall lifts and the wall rotates instead of resisting.

From chapter: Framed right

04 Where you may cut a joistSay why it matters, then open

A cut flange or a notch in the wrong place can drop a floor's strength by half. If it happens, the engineer specifies the repair.

From chapter: Your house

05 Taking out a bearing wallSay why it matters, then open

The beam is the easy part. The load still has to reach the ground, which is why new footings so often appear under the posts.

From chapter: Your house

06 Crown up, layout from one endSay why it matters, then open

A floor with crowns mixed up and down squeaks and shows in the finish floor. It takes a second per board to get it right.

From chapter: Your house

Words in this course.

18 terms in plain English, with the Spanish our crew uses. All 249 words across the school are on one page.

Crown Corona
The molding where the wall meets the ceiling.
Flashing Tapajuntas
Thin metal or membrane that steers water away from a joint, such as around a window.
Gable Hastial
The triangle of wall under the two slopes of a roof.
Glulam Madera laminada encolada
A big beam made of boards glued in layers. Often left showing.
Grain Veta
The lines and direction of the fibers in wood.
Hold-down Anclaje de sujeción
A steel bracket that bolts a wall to the foundation so an earthquake can’t lift it.
Lath Malla
The mesh or strips that plaster is spread onto.
Moisture content Contenido de humedad
How much water is in a piece of wood, as a percentage of its weight.
Rafter Cabio
A sloped beam that holds up the roof.
Ridge Cumbrera
The top line of a roof.
Shear wall Muro de cortante
A wall stiffened with plywood so the house doesn’t lean in an earthquake.
Sheathing Entablado
The plywood skin nailed over the wall and roof framing.
Soffit Sofito
The underside of a roof overhang, a beam or an arch.
Stringer Zanca
The sloped board that carries the steps of a stair.
Stud Montante
One of the upright framing pieces inside a wall.
Tail Cola
In a dovetail, the wedge shaped like a bird’s tail.
Valley Lima hoya
A sloped inside corner of a roof, where water collects.
Veneer Chapa de madera
A very thin slice of fine wood glued over a plainer panel.

Questions people ask.

Can I remove a wall in my Santa Barbara house?

Often, yes. If the wall is non-bearing, it is straightforward. If it bears a floor or roof, an engineer designs a beam and posts, and it is permitted and inspected.

Why is a 2x4 not 2 by 4 inches?

The nominal size is the rough-sawn size. After drying and planing, a 2x4 is 1-1/2 by 3-1/2 inches. Many older South Coast houses have true-dimension lumber.

What is a shear wall?

A wall sheathed with plywood or OSB, nailed to a schedule and anchored with hold-downs, designed to resist the sideways forces of an earthquake or wind.

What lumber is used to frame houses in California?

Mostly kiln-dried Douglas fir for studs and joists, with engineered lumber (LVL, glulam, I-joists) for beams and long spans, and pressure-treated lumber where wood meets concrete.

How dry should framing be before insulation and drywall?

California's green building code asks that framing be checked with a moisture meter before it is enclosed, at 19 percent moisture content or less. Wet framing shrinks later and pops nails and cracks drywall.

Sources and checks

Rules change with each code cycle, and the plans, the inspector, the adopted code and the maker’s instructions overrule any course. Code references are to the 2025 California Building Standards Code (Title 24), in force since 1 January 2026; check the local amendments of the city or county. This page was checked against these on 18 November 2026:

  • California Residential Code R602 (wood wall framing), R602.10 (wall bracing), R602.8 (fireblocking), R317 (protection against decay; corrosion-resistant fasteners)
  • American Wood Council, Special Design Provisions for Wind and Seismic (SDPWS)
  • West Coast Lumber Inspection Bureau and WWPA grading rules (grade stamps; S-DRY at 19% moisture or less)
  • APA, The Engineered Wood Association (plywood, OSB, LVL, I-joists, glulam)
  • USGS: 1971 San Fernando and 1994 Northridge earthquakes
  • AMN crew field guide: Framing
  • CALGreen (California Green Building Standards Code) 4.505.3, framing moisture content
  • Joist hanger manufacturers' catalogs and evaluation reports (fastener schedules)

Ask about your house

Matt Newman · 805 886 0988 · purchasing@amnbuild.com